Having problems with your ViewSonic VX1932WM LCD Monitor ?

Vx1932wm-3 monitor has stopped working properly,it will only stay on for around 2sec then lose digital signal and go black,same with analog.cant seem to make it stay on,the light on monitor is blue when it says lost signal, the graphics card is working fine 9400 series nvidia


Answers :

I had the exact same problem. It's a bad capacitor on your power board. It's most likely the 1000uF 25v one towards the center of the board. I noticed it on mine because the top of the capacitor was pushed out more than usual and it has some residue, which are signs of a burnt out/bad capacitor. (WARNING: There is a risk of electric shock when opening the power supply unit. Leave the unit unplugged for at least a few hours before working on it. Proceed at own risk!) Read on for a fix:
\015\012
\015\0121. In the back, remove the stand screw covers (x2) to access and remove the stand screws (x4).
\015\012
\015\0122. There will be a single screw under where the stand was attached on the screen. Remove it.
\015\012
\015\012The LCD/unit is sandwiched between the thin faceplate and back cover, which are held together by several clips:
\015\012
\015\0123. Carefully pry and remove the faceplate with a flathead screwdriver or other flat tool.
\015\012
\015\0124. There will be 2 screws holding the button circuit board in place. Remove the screws, unplug the small cable from the board, and remove the board.
\015\012
\015\0125. There are a few clips towards the bottom that hold the back panel onto the LCD frame. Pick at those until you completely remove the LCD unit.
\015\012
\015\0126. Remove the 4 side screws holding the LCD panel to the frame.
\015\012
\015\0127. Carefully disconnect the 2 sets of wires and the single ribbon cable from the LCD panel, taking note of their direction.
\015\012
\015\0128. Remove the 4 screws holding the large power control board in place, and disconnect the 2 cables connected to it (the smaller cable disconnects from the power control board, while the larger one disconnects from the other end).
\015\012
\015\0129. Locate the faulty capacitor and take note of its direction/polarity (+ and -). Use a powerful soldering iron to remove it from the board. I say 'powerful' because I could not get the factory solder to melt with my Weller at full 850 degrees. If you can't get it unsoldered, you can CAREFULLY pry it off with some pliers. If the connectors remain attached on the board, pry them off as well.
\015\012
\015\01210. Put in the new capacitor ($1.73 at Radio Shack), taking care not to bend or break the leads and taking note of its polarity. Trim the excess lead wire off and carefully solder into place.
\015\012
\015\012To finish, follow steps in reverse 8 through 1. Plug it in and test. If all is good, it should remain on. You might hear a tiny high-pitched sound when there is no signal or screen is idle. This happens with mine, but should be no cause for concern.
\015\012
\015\012Hope this helps and good luck!
\015\012
\015\012Questions? Email me: [email protected]
Hi,\015\012If the light on the monitor stays blue it is not losing the signal. Most likely cause is a fault on the inverter board which will cause the screen to black out.
Repair Help & Product Troubleshooting for ViewSonic VX1932WM LCD Monitor

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Vx1932wm-3 monitor has stopped working properly,it will only stay on for around 2sec then lose digital signal and go black,same with analog.cant seem to make it stay on,the light on monitor is blue when it says lost signal, the graphics card is working fine 9400 series nvidia


I had the exact same problem. It's a bad capacitor on your power board. It's most likely the 1000uF 25v one towards the center of the board. I noticed it on mine because the top of the capacitor was pushed out more than usual and it has some residue, ... ViewSonic VX1932WM LCD Monitor

The power light blinks solid blue every four seconds or so (it?s off in-between). The screen is blank. None of the buttons on the side function (such as ?menu?). I have a second similar monitor from the computer in the other room I?m using to type this proving the video card and cable are fine. We?ve always (as in years) left the monitor on (w/ a screen saver) but for whatever reason turned it off for four days when we went away recently. The monitor would then not turn back on. After leaving th


Hello,\015\012Two days ago I received a Gateway 900w FDP1975W Monitor from a friend. He told me that he would have to let it rest and it would work for about a hour or so and flash green with lines, then Flashing blue power light, then nothing. ... Gateway FPD1975W 19" LCD Monitor

Hp F 2105 MONITOR volume and sleep problem


... HP f2105 21" LCD Monitor

No color red displays.


If you think that electronic repair is very difficult to learn then you have to read this article where only by using a solder gun could solve a Monitor color problem. Of course there were many tough dog cases (very difficult to find out the fault) i ... ViewSonic G70fmb (Black) 17" CRT Monitor

RGB No Signal Message


First you need to check the cable at both ends, inside and out. Make sure it is plugged in, to the proper connector and that there aren't any bents pins. Now put this monitor on another computer, a laptop will do. Does it come on now? If so then ... Gateway FPD1975W 19" LCD Monitor

When i turn on my computer all it tells me is sva no signal input please check video signal


No Signal. No signal coming from the computer.The monitor is working, but there isn't any video signal coming from the computer.1.Could be a bad video cable. The one from the monitor to the computer. Do you have another ... SVA-USA VR 17S 17" Flat Panel LCD Monitor

NO SIGNAL What do I do?


These messages are normal when the computer truly goes into suspend mode or loses the video signal (such as when the computer is suddenly turned off).If the monitor displays any of these messages when the computer should be displaying vid ... HP PAVILION A6230N DESKTOP PC

Monitor has no picture


Yes! :)Your monitor is not the problem. Check all the connections from the back of the monitor, to the computer."No Signal Analog" means your monitor is working perfectly, however is not receiving signal from the computer. ... ViewSonic VX922 19" Monitor Flat Panel

I moved my computer to another room and now the monitor won't work. When I turn the computer on, the light turns green on the monitor for about 2 seconds then goes to orange and the screen stays black. If I unplug the blue cable, the light turns green and the screen displays no signal. Can you help me please?


On the back of your computer do you have 2 vga connections? 1 will be onboard and the second if you have it will be a graphics card, could you have plugged your vga into your onboard when you have a graphics card plugged in? if so youll need to plug ... PC Desktops

Problm with viewsonic va712b


Sounds like the operating mode is at a frequency or refresh rate that is outside the viewsonic operating specifications when in normal mode. possible solution: in safe mode access control panel, system, devices (hardware) and look for display. do a r ... ViewSonic VA721 17" LCD Monitor

Fujitsu-Siemens P15 TFT power/picture problem. it take time to turn on.


It does indeed sounds like the capacitors, I had this problem last year with a Medion monitor where it would turn on and off, when I spoke to Medion they did say that it would need a repair but at the time I wasn't enclined to pay the repair fees for ... Fujitsu Siemens Premium Line P15-1 15" LCD Monitor

Monitor Display Problem.


The first Polyview has a power supply problem (a short) and locks out the power until it is unplugged. You need to check the voltages inside the Monitor to determine which component/s are faulty. I hope you know electronics if not leave it to the r ... Polyview V17E 17" LCD Flat Panel Monitor

LG screen goes in stand by. I was using two monitors for several months, everything OK, now I decided to get a new LG Flatron instead of one of the monitors... and only this one goes in safe mode!! Two screens plugged in: Philips analogical working fine no problems. New LG Flatron digital goes in power save mode after few minutes Tried to plug in ONLY the LG, same problem after few minutes. Philips monitor no problems. So it HAS to be a screen function or problem of the LG? Computer: AMD + 3Ghz


Oke having a similar problem atm, this is what i have found so far. was trying to help a friend who has bought the same 19" LG monitor. When i connected the monitor to her PC i noticed that it was not the same connection as the previous one but it ha ... LG 19" Widescreen Flat Panel LCD Monitor

I was flooded last year and am now trying to put my PC together.....some wires/cables and all instructions were lost. I have main cable from pc to monitor, keyboard, speakers and mouse. As well as the cable from pc to monitor what others do I need please. Its an emachines 220 and it seems ok but the monitor is dead.


Make sure that your monitor is plugged into mains and that it is switched on. If the monitor is on you can see a "orange" light bottom left on the screen. If it comes on with a "No signal" on your screen, then you know that the screen is working. If ... PC Desktops

I have a Cornea 1702. It just stopped working altogether. It doesn't even show the menu nor does it search for a signal as it used to while scrolling thru options or select input! I think it's fried, but I remember some time ago i thought it was all done then it started working again. any thoughts?


OK, first off, I'd like to say that I've never worked on the Cornea 1702, but most monitors follow similar designs, especially generic brand monitors.So there are a few things I need to know: What exactly happens when you press the ... Cornea CT 1700 17" Flat Panel LCD Monitor

I NEED HELP PLEASE!!!!!!! PROVIEW 19" MONITER.


Does the led on front of the monitor stay blue or does it become amber ?\015\012If it becomes amber, then you are not getting a signal.\015\012No harm in trying this : You can try to see if it is a contact problem.\015\012With the m ... Proview PL926WBi 19" LCD Monitor

First let me say that the monitor DOES work on other computers. Just not this one. So it isn't the monitor. My monitor light is green until I plug it into my computer. It then goes amber immediatly and stays amber. Even when the computer is unpluged. If I turn the monitor off, plug it in , then turn the computer on,then turn monitor on, it starts out as green then says opms going into off mode and the light turns amber. There is no monitor hook up from the mother board. It has to plug into a vid


Many people use a vacuum on their computers, and I always advise against it. A vacuum creates Static electricity. Static electricity, will silently fry out your delicate computer components. You may not see it or feel it.To prove the vacu ... Dell Dimension 8100 PC Desktop

Acer Aspire M1640 PC monitor 'no signal', tower non-responsive.


I found the same problem (can't load BioS) but we are not alone as you can see on web about M1640 and M1641 it's very popular defectI made various test: cpu (pentiun e2180) pass the test mounted on another PC.I removed the two ram a ... Acer Aspire M1640 Refurbished Intel Desktop PC - Intel Pentium Dual Core E2160 1.8GHZ, 1GB DDR2, 120

HP desktop monitor problem


Hi try this ,,,\015\012\015\012\015\012Ensure the video cable is connected (and connected to the correct video port).\015\012\015\012Turn off the monitor using the monitor's power button and then restart th ... HP Pavilion a305w (DM181AR) PC Desktop

Monitor wont stay on- blue light is on. but screen keeps going blank.


Have you tried the monitor on another computer? If so, and it works, the issue is with your graphics settings on your computer. LCD and plasma based monitors often come with a protection circuit that disables the monitor if the synch or refresh rate ... Acer X193W LCD Monitor

My monitor says no signal


A friend gave me this computer because he got another and was tired of messing with this one ... he says he turned it off one night and it would never boot back up , sso i had a new 160 gig hd which is the same that was in it and i installed it think ... E-Machines eMachines Monitor E15T4

HP vs19e Computer turns on Monitor stays Black. blue light blinks


Easy step-by-step tutorial for replacing the caps in this monitor can be found at the link below:http://boredprojects.blogspot.com/2009/09/hpvs19e-monitor-fix.html ... HP vs19 19" LCD Monitor

My compaq presario 5000 (5WV286)will not exit sleep mode.when i power up my computer the yellow light stays on my monitor. when i hooked my monitor to another computer the monitor works fine.The key board lights (Scroll lock/Number lock & Tab lock lights all work,but when I press the Sleep botton nothing happens...the light does not go on or off..what is wrong with my PC? Daniel


It looks like port on your PC where monitor connected gone bad, now you can double check this connecting your PC to another spare monitor not the one which is already working, even one more thing sometimes it does happen that cable you are using with ... Compaq Presario 5000 PC Desktop

Cant figure out why my new lcd screen stays blue and dosen't show anything on it ... my laptop is working fine because i can see everything on a external monitor. Is there maybe a problem with inverter? When i switch displays the laptop screen goes black like it normally would,when both screens are on the laptop screen comes on blue but nothing appears on screen and the blue is faint,all the while windows and everything else works perfectly on eternal screen. I am lost please help?


Hi,This is known as " Blue Screen Of Death Error ". I really appreciate this time, we can easily understand your problem that Windows work perfectly on eternal screen But not on your laptop screen.This is actually not a softwa ... Dell Inspiron 1420 Laptop

Wont go to normal start up screen!!!


The screen that you're seeing is the self-test of the monitor, as it's already stated. It's commonly caused by having no signal coming from the computer to the monitor. You were advised to check the monitor cable, if you have already done that, then ... E-Machines eView 17f3 17" Flat CRT Monitor
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 1.0167 seconds