Having problems with your E-Machines eMachines W2686 PC Desktop ?

Emachine w2686 no display when boot up

\015 Emachine proablem when i start it up notthing show up on the monitor and the motherboard seems to be working fine.. almost out of ideas\015

Answers :

Couple things to check. First, check with different monitor. Their monitors are usually build by KDS and I think there was a bad series out there. Also check for any beep codes through speakers on startup, this can tell you bad ram or bad video out. Also try unplugging computer and removing CMOS battery inside (watch like battery). Lastly, If non of the above, a bad processor will allow the computer to come on but no beep, no boot, no nothing but fans and green power light. Hope this helps a little.....
Repair Help & Product Troubleshooting for E-Machines eMachines W2686 PC Desktop

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Emachine w2686 no display when boot up

Couple things to check. First, check with different monitor. Their monitors are usually build by KDS and I think there was a bad series out there. Also check for any beep codes through speakers on startup, this can tell you bad ram or bad video out. ... E-Machines eMachines W2686 PC Desktop

Can't restore my computer

Here's your GEEK-steer …\015\012\015\012Is the DVD you mention the manufacturer/reseller's recovery disk? You'll readily know because its user interface screens will display NON-microsoft business name such as eMachine's, etc. Or ... E-Machines M5305 Notebook

Toshiba Satellite 1400

To Access the Bios Setup Utility Here Is A List Of Key Commands And The Make/Model They Are For..\015\012\015\012Acer - Aspire, Power, Veriton, Extensa, Ferrari, TravelMate, Altos\015\012\015\012 ... Toshiba Satellite A35-S159 Notebook

Emachines monitor goes black while CPU is still working

... E-Machines eMachines Monitor E15T4

EMachine W3107 will not boot, no display.

Have you tried a different Graphics Card, looks to me like the onboard graphics card is at fault, there should be an AGP slot or PCI slot that you can plug a new Graphics card into then you should be fine... ... PC Desktops


Does the monitor work on another computer? does the computer work with another monitor? I the answer is yes to both then here is the most likely solution\015\012you may have the screen resolution and/or the refresh rate set too high on the ema ... Rosewill 19" 12MS DVI R911E LCD Monitor

Emachine windows xp welcome menu comes up and then black screen and we have sound but no picture changed monitors still does the same thing.never been used for internet

Puddycat_196,Did you just performed a clean installation to your system? Or maybe you just replace a new video card? The blank screen normally caused because of the resolution setting which is too high for the screen to support, or maybe ... PC Desktops

Cannot shut off & no display

The eMachines M5105 is notorious for failing to boot if left unplugged and powered off long enough for the battery to become mostly discharged. Plugging it in to AC power will cause the battery to start charging; and the hard disk drive to spin whil ... E-Machines M5105 Notebook

Ok i have a emachine c2280 we put a new power supply changed the ram and i have no video, there is also a red light next to the ram what isit..

Anytime. Just in case you there is any way you can get video to display. There is a setting in bios to change what controls the display adaptor. You might want to try to reset your bios and see if you can change this setting. Figure there is nothing ... E-Machines eMachines Desktop PC

Disabled video driver. Now unable to reboot emachines T5246

To reset bios with jumper settings: there is jumper on the board that has to be moved to the other adjoining pins, and then back. Hopefully it is marked. For sure check your owners manual, or google your mobo for the location of the jumper and exact ... E-Machines eMachines Desktop PC

New laptop lcd display not working

Check all usb connections i just fixed a emachine that seemed to boot up but no display would show lcd or ext. so i got to looking and one off the usb ports was broke and bent downt into the opening and shorting out when i removed it and turned back ... Gateway MT6451 Notebook

Hanging on boot screen

Try booting from a Flash ... E-Machines eMachines Desktop PC

My computer w2686 do not start

I'm assuming that when you say "unplugged" that are you are meaning to say that you're unplugging the IDE ribbon but still leaving the power plugged in to the device.Try resetting your CMOS settings by using the jumper on the motherboard. ... E-Machines eMachines W2686 PC Desktop

On boot up the emachine now beeps every 5 seconds

Reboot with "F8" held down.\015\012you are only booting to bios and minimum disk software. This may give you an indication of your monitor or video driver status.\015\012\015\012If you can borrow another monitor from someone, that ... E-Machines eMachines Desktop PC

Emachines 1900+ gets power to the monitor and computer but wont boot

If your display is LCD, sometimes, the backlight behind the LCD won't light up, but the LCD might be working. You might try shining a very, very bright light on the screen to see if there is an image being produced. Sometimes I get lucky and find a l ... E-Machines eMachines Refurbished EMA eMachines PC Desktop

I have an emachines t5226 with vista. it will not boot.the fans run and that's all it will do. the dvd drive spins but won't read the boot cd. when the computer crashed I turned off the power strip and turned the strip back on. I turned the computer on and it would boot.

Hi! if your pc is still powering then theres no problem with the PSU, if your pc boot and have a display on your monitor then theres no problem with your VGA card and RAM but if your PC don't have display then you must check your VGA and RAM it maybe ... E-Machines eMachines W2686 PC Desktop

Emachine destop not recognising acer lcd monitor

It sounds more like the computer isn't starting up. The "no signal" message is coming from the monitor itself to tell you it's on but there's nothing coming in to display. Normally no special drivers are required for the monitor, and you'd see at lea ... Microtek C593 15" Flat Panel LCD Monitor

Emachine T2385 Won't Boot in Normal Mode past Windows XP Screen

The first thing I would check is your video card (usually driver) problem. Start windows in safemode with networking. If this problem has occured after updating the video card driver you may try rolling back the driver to a previous version, otherw ... E-Machines Celeron 2.3GHz (rb-t2385)

Boot up emachine t3265 win xp wont boot up gets to windows frame then goes blank. safe mode locks up after displaying files last file shown mup. any help would be appreciated.

You may try "Last Known Good Configuration"\015\012 \015\012Boot the operating system with the “Last Known Good Configuration” feature. To use this:\015\012\015\012R ... E-Machines eMachines Desktop PC

Come on, boots up, then shuts down 5 - 10 minutes later.

I recommend checking your power settings in the control panel, it should actually be under display settings. It may under those settings somehow be set to shutdown in 10 minutes. You can find the power settings, sleep mode, UPS, and hibernation under ... PC Desktops

Need boot load for emachine T2484

Hi,\015\012\015\012You need to enter your CMOS/BIOS setup and set your "First Boot Device".\015\012\015\012Immediately after powering up, press the "Del" key, display will show CMOS/BIOS settings. Verify that all your hard disks are being detected/re ... E-Machines eMachines Desktop PC

I have a eMachine with XP and tried to use restore disks. The first disk started working then got an error message about output to A:/Ghosterr. I called the tech support # and was told it was out of warranty, that my disks were damaged and I couldn't buy new ones. Said I had to find local technician to work on it. Does this sound correct? Reading here it sounds like I can try that F8 trick above to restore?

I am not sure what you mean by the F8 Trick. If you mean hitting F8 (or F5) at boot up time, that will get you to a boot menu where you can choose to boot into safe mode with network, without network, and a few other options, then yes, that is the t ... E-Machines eMachines Desktop PC

Emachines M6807 suddenly has display problems after years of working great...as soon as laptop display starts to light up,even while booting,before windows starts, all the normal images on the screen are covered by strips of bars and lines which obscure everything underneath. i have tried rolling back the video driver and tried using the vga output to my tv and the display is equally obscured there,too. Not sure what to do now

...pay me and I'll tell you how I fixed it...I know one thing, software companies and manufacturers are getting away with sabotaging peoples older PCs and laptops by corrupting working machines with "auto updates" . These harmful changes can ... E-Machines EMA M6807 PC Notebook

Computer is not working

Disconnect EVERYTHING FROM EVERYWHERE!Reset CMOS.Grab the main power cable from the power supply unit and attach the ATX connector to the motherboard.Make sure the processor fan is connected to the correct socket on the motherboard ... E-Machines eMachines Desktop PC

My laptop turns on but displayed black background & white cursor

I would boot in safe mode and attempt to run a scan for viruses or malware. That is what I would think the problem was\015\012\015\012You could also do a system restore to before this problem started in safe mode. If you dont know how to get to ... Acer eMachines 520-2890 Notebook
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.4399 seconds