Having problems with your E-Machines eMachines Desktop PC ?

EMachine T1440 will no boot on

\015 My emachine T-1440 Desktop will not boot on. I unplugged it for a week while on vacation with no previous problems until coming back from vacation and replugging it. No reboot disc available. What are my options?\015

Answers :

There is a battery inside the pc, remove it and replace it with a new one. Leaving it unplugged for that long taxes the battery too much. This should help and also plug everything in and reset the power switch on the back.
Repair Help & Product Troubleshooting for E-Machines eMachines Desktop PC

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Unbootable EMachine My T1440 EMachine will no longer boot. I'm sure it's hardware related since the PC is over 6 years old and I always ran a firewall/av software and never opened unknown attachments. I tried to load the restore disk that came with the PC but to no avail. Any thoughts what hardware may have gone bad or how to check it out? Thanks, Dan


Unless you have data on your HD you really want, i would chalk this up to a loss. If you cant boot up, and you cant get into setting while booting up then you probably need to take it somewhere. Being as its so old, i would consider a new PC. There c ... E-Machines eMachines Desktop PC

EMachine T1440 will no boot on


There is a battery inside the pc, remove it and replace it with a new one. Leaving it unplugged for that long taxes the battery too much. This should help and also plug everything in and reset the power switch on the back. ... E-Machines eMachines Desktop PC

My pc was doing this but now it's doing something different but simular


Try this: boot into the bios, set the boot order to cd rom first,hard drive 2nd and either one to 3rd. Hit F10 to save changes & exit. Put in your Windows cd. It should come up to a screen that says "Hit any key to boot to cd", do that. Set up sh ... E-Machines eMachines T3830 PC Desktop

Emachine boots to bios with a new hard drive installed


A computer cannot boot straight to the bios, unless under 2 circumstances. First, the jumper on your motherboard is not set into the right location. (If you never mess around inside of your computer, this shouldn't be an issue...) The only other way ... E-Machines eMachines T3830 PC Desktop

I am trying to replace the hard drive in emachine 500is. Now the computer will not recoginize the cd rom to read the windows xp set up disk.


Go into BIOS Setup, and in Boot Order, change the first boot device to CDROM.How?To go into BIOS Setup you start tapping either the DELete key, or the F2 key, ->Right After you see the eMachines logo. If you miss this window of o ... PC Desktops

Windows doesn't recognize recovery partition after os reinstall


The issue you are having involves using multiple systems,...If your emachine came with vistan and you installed xp, you voided your warranty status...However remove your dual boot and stick to vista if you wanna keep your restore partition working pr ... E-Machines eMachines Desktop PC

EMachine W3107 will not boot, no display.


Have you tried a different Graphics Card, looks to me like the onboard graphics card is at fault, there should be an AGP slot or PCI slot that you can plug a new Graphics card into then you should be fine... ... PC Desktops

EMachine T1840 Will Not Boot


Well sounds like you are in quite a pickle. If the restore is not functioning properly you have one of a few options. Continue with the restore without backing up, take it to a computer specialist and have them back up your information and redo the ... E-Machines -T1840-CELERON-1.8GHz,40GB Desktop Computer System (1000000127)

Emachine- will boot up 3-4 times before computer


This could either be a operating system problem or hardware. \015\012\015\012O/S problem could be actually caused by several things but eventually it might not work at all. It can also be caused by a recent and rather nasty virus going ar ... PC Desktops

Can't restore my computer


Here's your GEEK-steer …\015\012\015\012Is the DVD you mention the manufacturer/reseller's recovery disk? You'll readily know because its user interface screens will display NON-microsoft business name such as eMachine's, etc. Or ... E-Machines M5305 Notebook

2 emachines won't boot


Are you attaching them properly\015\012if so then it is something other then power supply\015\012something has caused both power supplies to blow\015\012have you installed anything in the first emachine you talk about ... E-Machines eMachines Refurbished EMA SYSTEM BOARD MODEL T2984 eMachines (102257) PC Desktop

Emachine reboot problem


First of all remove ant cd from drive when booting up uinless you are using a bootable windows disk. if the problem still persist when then computer starts booting up keep pressing f8 until you get the choice to go in to safe mode. Once in safe mode ... E-Machines eMachines Desktop PC

Black screen On trying to boot my laptop it did not boot at all.i need real solution now


- I had the exact same problem with a eMachines W340UA and other machines. I'm not sure what this does, but I resolved it by booting into Safe-Mode. Upon successful boot into Safe-Mode (without Networking), I restarted the computer in the normal mo ... PC Laptops

Installation windows xp emachine t5082


You must find "eMachine" XP USB drivers for your computer.\015\012If all USB support is "enabled" in BIOS, the conflict is with drivers.\015\012XP is loaded with many generic drivers, however eMachines is proprietary and requires eMachine ... E-Machines T5082 PC Desktop

Toshiba Satellite 1400


To Access the Bios Setup Utility Here Is A List Of Key Commands And The Make/Model They Are For..\015\012\015\012Acer - Aspire, Power, Veriton, Extensa, Ferrari, TravelMate, Altos\015\012\015\012 ... Toshiba Satellite A35-S159 Notebook

Emachines W3052 Gets stuck on logo screen when starting up.


My computer does a similar thing, the issue with mine is the mother board which requires everything to be at a certain temperature. Let it run on the start screen for a couple minutes and hit the reset button. If it doesn't boot up you're going to ha ... E-Machines W3052 PC Desktop

Disabled video driver. Now unable to reboot emachines T5246


To reset bios with jumper settings: there is jumper on the board that has to be moved to the other adjoining pins, and then back. Hopefully it is marked. For sure check your owners manual, or google your mobo for the location of the jumper and exact ... E-Machines eMachines Desktop PC

Replacement DVD-ROM drive


Hi there.get hold of a boot cd or a windows install disk, set the boot options to boot from the cd drive, if the cd or dvd starts to boot and you get windows loading window then chances are that the lens on the drive is dirty and need cleaning, ... E-Machines M5305 Notebook

MY EMACHINE DESKTOP RECOVERY CD DOENT WORK


Hello \015\012When booting up pc have you held the delete key or f2 key down to bring up the boot menu?Should be a option of cd dvd or hdd to boot first.\015\012\015\012You want the cd dvd boot option on top or first.tThen reboot pc ... E-Machines eMachines Desktop PC

Hanging on boot screen


Try booting from a Flash ... E-Machines eMachines Desktop PC

I can not get of help and support mode. emachine t3990. I entered doagnostic thru emachine help and support. but when restarting computer several programs are not running such as: search, help and support, sound, printer, networking. tried safe mode, but no help. have restore disc, but dont want to use, due to not having back up. please try to give me good news. thank you very much, and merry CHRISTMAS TO ALL.


You can repair your windows without lost data.\015\012For that you need to boot your computer with restore disk.\015\012For that when you power up the computer press F1 or F2 or "del" key to enter in bios.Then go to boot menu and set firs ... E-Machines eMachines Desktop PC

Need to change T1742 Video Card FRAME memory. To boot from CD with Perfect Image on eMachine T1742 unit I need to change the Video card Frame memory (increase) so that the Perfect Image program can boot properly. What function key gives access to change the Video card Frame menory? Thanks for any help... JT [email protected] . To boot from CD with Perfect Image on eMachine T1742 unit I need to change the Video card Frame memory (increase) so that the Perfect Image program can boot properly. Wha


... E-Machines eMachines T3830 PC Desktop

Emachine M5105 that won't boot up.


I suspected the IDE cable is not properly connected to your hard disk. Check connections and boot up machine normally. ... E-Machines M5105 Notebook

Emachines when I boot up my computer the Emachines logo appears, fan turns on and does not boot.


Hi Che,There are a variety of issues regarding a computer not booting up. There are hardware and software issues associated with it. You can approach the problem through the following steps:1. Clean your unit with a soft brush, avoi ... E-Machines eMachines Desktop PC

My emachine freezes after it boots up. I had


I must say at the front that you seem to have the machine looked at professionally and received advice. They couldn't fix it ... I'm not sure I can build on that diagonosis. I do have a few ideas, however. This is a case where the messenger is tel ... E-Machines eMachines Desktop PC
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3408 seconds