Having problems with your Compaq Evo D500 PC Desktop ?

No input signal on monitor after changing resolution

\015 Hi all, just today I was upgrading a compaq desktop 2.4Ghz pentium 4. I put in a 1Tb hard drive and tv tuner and also a video card which didnt help, so I went back and put in the original which was in the PC. Everything was fine I installed windows and in a happy moment I changed the screen resolution to some high value and it was working fine and the problem started when I shut down and restarted again. There is no input signal to the monitor even though the cpu seems to be working fine.I tried changing the video card the hard drive itself( with a 40gig), the monitor , connected the cable to another input source on the cpu and almost everything. But to no avail. PLease Help!!!!:-(\015

Answers :

Hi,

While booting press F8 , Go to safe mode and change the screen resolution and reboot the system.

Hope this helps
Siju.D
The motherboard no longer works
Repair Help & Product Troubleshooting for Compaq Evo D500 PC Desktop

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

ViewSonic VX922 monitor - black screen - green power light flashes


PLEASE read Carefully so here is a fix for the green blinking light ...the monitor is going into shutdown....protect mode......THIS is ...Only for the seasoned electronic service tech ......YOU NEED TO BE into Electronics ..or have electronic backgro ... ViewSonic VX922 19" Monitor Flat Panel

No input signal on monitor after changing resolution


Hi,While booting press F8 , Go to safe mode and change the screen resolution and reboot the system.Hope this helpsSiju.D ... Compaq Evo D500 PC Desktop

Osd lock in my LCD


Check your switchers resolution settings .....\015\012You might have to change your resolution settings....\015\012 \015\012This solution is for AOC Monitors...... ... X-10 LM929 19IN LCD 12X10-.294MM SPK BLK

Input Signal Out Of Range


Some monitors have low resolution, that if it doesn't support that resolution then you'll expect an "input signal out of range" message on screen. try to boot on "safe mode" if it works then you have to lower your screen resolution at "display proper ... HP Pavilion F1523 15" LCD Monitor

No input data


Generally this means that the monitor is not getting a signal from the computer.\015\012\015\012You can also get this message when a computer goes into standby. Pressing a key or moving the mouse can bring it back. \015\012\ ... HP PC Desktops

W17e says "input not supported"


Hi - here's what I found about your wide screen monitor:The HP Pavilion w17e LCD wide-screen monitor has the following features:\015\012 \015\012\015\0121440 x 900 factory-set resolutio ... Acer AL1916W 19" LCD Monitor

INPUT SIGNAL OUT OF RANGE


Some how your screen resolution has changed above or below what your monitor can display. you need to boot your computer using another monitor that can work with the resolution your computer has switched to(i used a spare crt monitor when it happened ... Relisys TL775 17" LCD Monitor

Signal out of range


1: Signal out of range meas the monitor can't handle the input refresh rate. lcd and Tft monitors usually supports 60 and 75Hz refresh rates.2: The Resolution you are using to view the desktop is too high, this number is depending on the size o ... Kogi L7CH Monitor

Monitor screen stuck at input not supportedhow do I go back ?


Assuming you have not changed the connection to your monitor (from VGA to DVI signal, for example), or that you have not messed around with the display settings, further below may be the situation. Else, you need to access your LCD menu and choose t ... HP Computer Monitors

I just go a nw hp 2009m and I cant get it to work it clicks on for just a second then goes off It works fine on my other flat screen hanns g


Is your other flat screen bigger than the hp 2009m? If so, it may be set at a resolution that the new monitor isn't capable of hitting. Try changing your resolution before plugging it back in. That MAY work to help you. If it's not that, then for som ... Computer Monitors

Dell 2407WFP Monitor losing signal and having colored line artifacts


... Dell UltraSharp 2407WFP 24" LCD Monitor

Need to change resolution but cannot get onto desktop to do so as the monitor just goes to sleep


Plug it into your laptop and change the settings to the monitor to 800 by 600 pixels, then change the refresh rate to 60 hz or you could change it to 1280 by 1024 pixels and 60hz but it should work with 800 by 600 too, then plug it back into your des ... HP L1706 17" LCD Monitor

Laptop to tv


If your tv don't have s video input,you can get an Svideo to RCA cord.\015\012If the tv does have s video input,just get an s video cable and plug it into the tv and computer s video ports and follow the steps below for setup.\015\012 ... Toshiba Satellite L305D-S5895 Notebook

Benq FP222W Every time I switch on, or the signal to the monitor changes, the message "Input D-sub" appears. This is very distracting. Is there any way to stop this? Thanks Don


Try putting the resolution on 65hz if that dont work then try\015\012different resolutions on the monitor. Right Click in a open area on your desk top and click properties and the click the monito tab to change the resolutions. ... Computer Monitors

I have a tv screen which i use for my computer.I have the hdmi cords going from the video card on the back to my tv.why is it not working


\015\012Identify your TV's input connections. Most TVs these days have three basic types of inputs. You have your coaxial cable input, the same as your cable box or satellite, an RCA composite input (the yellow, red and wh ... Acer Aspire T160 (AST160UA3400) PC Desktop

Trying to use my hp laptop with sony lcd hdmi tv for movies


You should have an S video port on both tv and computer.\015\012\015\012If your tv don't have s video input,you can get an S video to RCA cord.If the tv does have s video input,just get an s video cable and plug it into the tv and c ... HP Pavilion dv6000z Notebook

Error on monitor: Input signal out of range. using VGA cable and laptop is right next to monitor Hannspree 23" HF237 LCD monitor


Hello mcarsten,Your monitor may not be configured to the correct resolution for the second monitor. If you right click on an empty space on the desktop and then select properties, the display properties will appear. Click on the last tab ... Hannspree Computer Monitors

I cant make my e1505 view on my tv do i need to change a setting to tell it where to show?


\015\012At the rear or side of the PC there should be either or both of a 15 Pin DIN Plug, HDMI socket. or a Yellow RCA or 4 -7 pin DIN. Now IF these are present then YES you can connect to a TV. Now some TV's have a connector a DB1 ... Dell Inspiron E1505 Notebook

Same problem, acer sucks imo


Similar problem with Acer AL2216W - sometimes DVI input don't work properly (but analog in works well in the same time) and I have blackness on panel - I just need to change resolution on my ATI video card for a moment and return to native 1680x1050 ... Acer AL1916W 19" LCD Monitor

Input Signal Out of Range


I have been having the same problem with my hpvs17 monitor when i start to use my web browser on linux distros. Now, for the next few days i am going to try my system on a regular crt monitor. if the monitor does not crash, than i will have to say th ... HP Vs17 17" LCD Flat Panel Monitor

New video card wont work, acer monitor no signal


Ok the IGFX is the on motherboard video you will need to set the cmos to clear the setting you did or move the video cable to the motherboard output.after you have used the bios to switch back to the AGP you can start widows in safe mode to acc ... Acer X193W LCD Monitor

Inout signal out of range Answer Failed: retry


It shows out of range because the PC is sending out the video signal that is higher than the monitor can display, you need to set the PC video resolution to the native resolution: 1024 x 768 @60Hz. You can reboot the PC into save mode (hitting F8 key ... IBM ThinkVision L151 15" LCD Monitor

"No signal detected" when LCD connected with DVI-D Cable


Thank you for providing your configuration details.\015\012You have failed to specify wheather or not your LCD Display is under Warrenty.\015\012\015\012Perhaps these simple trouble shooting procedures will get the job done.\0 ... BenQ FP71E 17" LCD Monitor

How do send monitor signal to my tv


Not familiar with this particular model but a lot of factors are involved here and it may not be possible depending on both the television capability, and the video hardware on that model of computer. However your question about how to SEND the signa ... Compaq Armada M700 Notebook

Laptop to tv


\012Right, well, IF your TV has a DB15 Female Plug on it then you CAN, connect it up and it will work, as a second "Monitor". OR If the laptop, has a "Composite Video" a Yellow RCA socket, then you ... Acer Aspire 5500 5570-2609 Laptop
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.5109 seconds