Having problems with your BenQ FP71E 17" LCD Monitor ?

BenQ Q9T4 monitor displays "no signal detected"


Answers :

If your video card can be remove , try to clean it, but if not buy a new plug and play video card.
\015\012
\015\012your problem is your video card
Check and see that all cables are plugged in their respective sockets. if it is. Then your video card is at fault have it replaced.
Repair Help & Product Troubleshooting for BenQ FP71E 17" LCD Monitor

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

"No signal detected" when LCD connected with DVI-D Cable


Thank you for providing your configuration details.\015\012You have failed to specify wheather or not your LCD Display is under Warrenty.\015\012\015\012Perhaps these simple trouble shooting procedures will get the job done.\0 ... BenQ FP71E 17" LCD Monitor

BENQ FP737S Monitor shows "No Signal Detected" on startup


First problem could be the hdmi cable you are using is loose or broken.second, the display mode you selected was wrong, try to go to desktop and right click and choose nvdia control panel and choose the nview display mode to use,select the only use o ... BenQ FP71E 17" LCD Monitor

I turn my monitor on and it displays BENQ and then goes to -No Signal Detected- Power light changes to orange..help?


IT MUST BE A DPI.IF UPPER THAN 60Hz THE PROBLEM WILL BE OCCUR AGAIN.I THINK ... BenQ FP71E 17" LCD Monitor

BenQ Q9T4 monitor displays "no signal detected"


If your video card can be remove , try to clean it, but if not buy a new plug and play video card.\015\012\015\012your problem is your video card ... BenQ FP71E 17" LCD Monitor

NO SIGNAL What do I do?


These messages are normal when the computer truly goes into suspend mode or loses the video signal (such as when the computer is suddenly turned off).If the monitor displays any of these messages when the computer should be displaying vid ... HP PAVILION A6230N DESKTOP PC

No display on SyncMaster 710N


I used 2 resistor of 100 ohms (1/8W) to make one of 50 ohms. Like others instruction, just put the 50 ohms resistor between pins 5 and 6 of this chip and the problem is solved. ... Samsung SyncMaster 710N 17" LCD Monitor

HP desktop monitor problem


Hi try this ,,,\015\012\015\012\015\012Ensure the video cable is connected (and connected to the correct video port).\015\012\015\012Turn off the monitor using the monitor's power button and then restart th ... HP Pavilion a305w (DM181AR) PC Desktop

I need to find the VGA controller for the Dell 2005FPW monitor


You can use on all vga cards(you dont need any special controler), this monitor has a USB hub\015\012and its is detected normaly on winxp or above, and the vga cards detect the monitor auto.\015\012i give you the monitor ... Dell UltraSharp 2005FPW 20.1" LCD Monitor

Mag monitor doesn't display bios post


The BIOS is sending the display information to the monitor but, when you turn your PC on, the LCD will be sleeping and it will take 1~2 seconds to wake up when receiving the display signal. The monitor is working and even if the BIOS messages aren't ... Computer Monitors

I've been trying to use s-video cable to connect


\012\012At the rear or side of the PC there should be either or both of a 15 Pin DIN Plug, HDMI socket. or a Yellow RCA or 4 -7 pin DIN. Now IF these are present then YES you can connect to a TV. Now some TV' ... Acer Aspire 3690-2196 Notebook

I've got a Toshiba Satellite Pro L300 that I'm trying to connect to my very old TV (16 years). I'm going through the VCR. I thought I could connect the laptop's VGA to the RGB port on the VCR, tune to the right channel, adjust the display on the laptop & poof --- big screen monitor. Well, no such luck. Any help would be appreciated. Oh, it go directly to the TV, I would need to convert the PC's VGA to coaxial. I thought it would be easier going through the VCR's RGB.


No that will NOT work, first the PC's VGA doesn't have any "Channel" Second you must install Drivers for said VGA card, and the card MUST have a TV out connector either SVHS, or Composite, video out, or as of late HDMI. You Cannot "Receive" a VGA, si ... Toshiba Satellite L300-EZ1004V Notebook

Laptop to tv


\012Right, well, IF your TV has a DB15 Female Plug on it then you CAN, connect it up and it will work, as a second "Monitor". OR If the laptop, has a "Composite Video" a Yellow RCA socket, then you ... Acer Aspire 5500 5570-2609 Laptop

No picture or power green light just blinks - Sceptre X9G Komodo II (Black) 19 in. Flat Panel LCD Monitor


Carrizosas, Tell me more. How old? Approx. total "ON" hours of use? Did it display a "bright, crisp, full color text and graphics and pictures the day before? Does this unit have a lay on floor "BLACK BRICK" ac to dc supply, or only a 3 wire line cor ... Sceptre X9G Komodo II (Black) 19 in. Flat Panel LCD Monitor

My monitor gets no input signal, computer does


Try the montor on the external vga connection of the laptop. You can swap the signal from the laptop screen to the external monitor using the swap key (usually a FN key). You can do this whilst the laptop is up and running. If you see the display the ... Xerox XA7-17i 17" LCD Monitor

PCV-RS720G Sony Vaio : BFG 5500 installed and wont display


Hi thereBoot up in safe mode, F8 on start up, if it lets you into windows, go to the device manager and uninstall the graphics drivers, then reboot the pc, let the PC detect the new card and try install the drivers, have your driver CD in the C ... Sony VAIO PCV-RS720G (027242658103) PC Desktop

Can't find video signal


If screen says "Signal cable not connected " all the time till power led switches to Amber chances are monitor is ok and problem is with graphic card or cpu.Connect to Known working CPU and confirm that monitor is the problem.\015\012If same pr ... BenQ FP731 17" LCD Monitor

Monitor 'no signal detected' issue.


Try going to control panel, click hardware and see if you see the monitor if so click on and click refresh. Make sure you have the disk forthe monitor in case it asks for it. You can also go online and download them first. ... Computer Monitors

Ibm xseries 235 eserver....all of a sudden stopped booting...it was set up through a kvm swtich, the kvm detects a signal and lights up the apprpriate port, yet nothing is displayed on the monitor. disconnected from kvm, connected directly to a monitor, and still no signal....only error light is indicating a HDD problem, that has never failed to put something on the display before, im kinda stuck on how to troubleshoot....i know the drives are good, i guess it could be a LSI adapter problem, but


The drives were working right before it rebooted....it booted into windows prior to this. i shut it down to install another drive, turned it back on and nothing...not even a post screen. i removed the hard drive from the scsi controller and it stil ... IBM eserver xSeries 235 8671

Different color test patterns keep cycling .


This could be a computer or monitor problem. The reason that display shows up is because the monitor is not getting a power good signal from the computer. If a monitor doesn't get a power good signal it goes into test mode. It could be the monitor ... Dell E176FP 17" LCD Monitor

LG 700E monitor's power LED blinking continueously, no display


The monitor is probably on protection.To start unplug monitor\015\012from power and from computer and test computer with different monitor\015\012to find out if it is monitor or computer fault.If it is computer fault and no vi ... LG 500LC Monitor

Nvidia Vetro Geforce 6800GT on E510? Need help setting up max displays MD 219 dual displays


... Max Displays MD-219 (Gray) 19 in. Flat Panel LCD Monitor

I have a s-video output and hooked it up though a cable to the yellow rca on the back of the tv. how do i get that to work and watch the computer screen on tv


Ok there can be several ways to do this\015\012 now it depends on the outlets on both your tv and your computer and video cards installed some computers and tvs require a converter to let the signal out properly and to the best possible resolut ... HP Pavilion dv1000 Notebook

HP 1940 turns off after a second or two desktop appears with a message no signal detecked


No signal detected is displayed when there is no sync pulse detected by monitor. look in the monitor cable connector and see if you have a pin bent down. same at video connector at pc. if no bent or missing pin it probably bad in monitor itself. do u ... Computer Monitors

Screen Goes Blank


Ive seen this on other monitors. Look for a 1 and 2. Some monitors do NOT auto detect a signal, and this one might not. Look for a way to set the monitor from Digital input to VGA input. Try that and see. ... Dell E173FP 17" LCD Monitor

My monitor will not come on when power is applied automatically. the monitor does not come up when my system comes on. I just replaced the monitor which i swapped same exact monitor, but this one will not boot when the system comes up.


Please work through the following steps to troubleshoot your no power problem with a ViewSonic Monitor:\015\012\015\012Troubleshooting Power Issues: \015\012\015\012Disconnect and securely reconnect ... ViewSonic E70f 17" CRT Monitor
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.5248 seconds