Having problems with your PC Desktops ?

EMachines T3656 Desktop wont boot and no signal to monitor


Answers :

Try to check the monitor cable if it is properly connected to your motherboard. If you will have a video card you need to attach your monitor cable to the video card.
Repair Help & Product Troubleshooting for PC Desktops

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

EMachines T3656 Desktop wont boot and no signal to monitor


Try to check the monitor cable if it is properly connected to your motherboard. If you will have a video card you need to attach your monitor cable to the video card. ... PC Desktops

Emachine destop not recognising acer lcd monitor


It sounds more like the computer isn't starting up. The "no signal" message is coming from the monitor itself to tell you it's on but there's nothing coming in to display. Normally no special drivers are required for the monitor, and you'd see at lea ... Microtek C593 15" Flat Panel LCD Monitor

DELL INSPIRON 1501 won't BOOT...and LEDs flashing


Hi..This is an Hardware Failures: Doesn't Boot Up.First of all, most of the\015\012hardware failures that are going to be presented in this article\015\012require you to disassemble the l ... Dell InspironTM 1501 Notebook

Black screen on my desktop, and connect pins are broken & bent


You'll get either no signal or missing color(s) if pins are bent or missing.Carefully bend pins back with small needle-nose pliers. Pin 9 is missing by default - if any other pins are missing or broken, you'll need an expert to wire a ne ... E-Machines eMachines Desktop PC

RESTORE DISC I have an Emachines Desktop. I am trying to do restore cd. Monitor does not seem to have a problem as it is running a test screen but nothing is coming up when I insert CD.


The 'test screen' of the monitor means only that the monitor would display if it receives an input signal.\015\012Make sure it isn't something simple like dislodged video connector on the back of your system box.\015\012You may even want ... E-Machines eMachines Desktop PC

LCD monitor signs "no signal" on eMachines t3418


E-machines had had a long history of bad power supplies. I've seen many of these machines go bad and when they do they take out the video chip (Nvidea) with it, usually shutting down the whole machine. I've never seen one operable. You might be ab ... E-Machines eMachines Monitor E15T4

"No signal detected" when LCD connected with DVI-D Cable


Thank you for providing your configuration details.\015\012You have failed to specify wheather or not your LCD Display is under Warrenty.\015\012\015\012Perhaps these simple trouble shooting procedures will get the job done.\0 ... BenQ FP71E 17" LCD Monitor

EMachine Desktop Computer


This is most likely an issue with the powersupply being faulty, contact Emachines and tell them the error(as well as model and all that). They will then most likely send you a power supply that you can easily install yourself. Its just four screws in ... E-Machines eMachines Desktop PC

Screen comes on says Acer then No Signal, and goes out. if shut power off and then back on get same result.


This means the monitor believes it's not connected to the computer. Verify the cables first of all. Then try booting in safe mode (F8 key at PC startup) in order to verify that the PC is sending data to the proper video port (you might have a dual VG ... Acer AL2223W 22" LCD Monitor

The computer wont boot up. and the screen wont display anything!


Take a multimeter and verify the AC adapter. If it is ok, remove the battery. When you push the power on button do you have any activity ? If there is no activity the motherboard is defective. If you have some activity (leds on, fan activity etc.) : ... Dell XPS M1210 Notebook

Wont boot no BIOS and oly a white screen


Typically I have found that it is a connector that is the problem. You're getting power (lights the screen) but you aren't getting a digital signal (Screen Memory Map & Desktop). Check the mylar ribbon cable on the left, that is going under the hing ... Compaq Presario 1700 Notebook

Computer randomly fails to boot


How many video cards do you have installed? ... E-Machines eMachines Desktop PC

Not booting up showing green light wont show on screen


Power supply failing. Inside your personal computer power supply are components that can easily fail, and have been a known issue. Nor just Compaq computers, but a vast majority of pre-made computers.Electrolytic Capacitors. ... HP Compaq Presario SR1610NX (ED865AA) PC Desktop

I turn on the desktop and the monitor only says no input signal input2: HD15 go to power save what do i do?


Hi jiheeahn! I wiull be glad to assist you. lets isolate the issue. The reason why the monitor says no signal input2: hd15 got to power save. the connection from the monitor to the desktop computer is disconnected or its not connected to the right in ... Sony SDM-HS73P 17" LCD Monitor

Massive series of problems with IBM Thinkpad


Probably itz either minor case of software corruption/improper ground/cpu fan..or major case of faulty or defective main board/ram/addon/daughter cards....plz do check the following as in order:..the Hardwa ... IBM ThinkPad R40 2897 Notebook

No picture or power green light just blinks - Sceptre X9G Komodo II (Black) 19 in. Flat Panel LCD Monitor


Carrizosas, Tell me more. How old? Approx. total "ON" hours of use? Did it display a "bright, crisp, full color text and graphics and pictures the day before? Does this unit have a lay on floor "BLACK BRICK" ac to dc supply, or only a 3 wire line cor ... Sceptre X9G Komodo II (Black) 19 in. Flat Panel LCD Monitor

EMachine W3107 will not boot, no display.


Have you tried a different Graphics Card, looks to me like the onboard graphics card is at fault, there should be an AGP slot or PCI slot that you can plug a new Graphics card into then you should be fine... ... PC Desktops

Steps tp instal Nvidia 6200 AGP card


Once you have your computer unplugged and taken apart to the point where you can access the AGP slot, take off the small metal cover on the back of your computer (usually fixed with a single screw). Gently place the Nvidia graphics card into the slot ... AMD eMachines Desktop System w/ 17'' CRT Display, 2.0 GHz Athlon 64 3000+ (W3400)

I have an emachine T2984 that won't boot. No noise of any kind. I had another emachine T2625 that was working. I took the power supply out of the T2984 (that wouldn't boot) and put it in the T2625 and it worked. Can I assume that rules out a faulty power supply? However, now when I put the original power supply back in the T2625, it now does not boot up. The power supply seems to work, but I get a "no signal" message on the monitor. Any suggestions?


Power supply sounds fine. If the pc won't power up it could be your motherboard. If the pc is powering up and you get a 'no signal' on your monitor it could be your gpu. ... E-Machines eMachines Refurbished EMA SYSTEM BOARD MODEL T2984 eMachines (102257) PC Desktop

Input Signal Out Of Range


Some monitors have low resolution, that if it doesn't support that resolution then you'll expect an "input signal out of range" message on screen. try to boot on "safe mode" if it works then you have to lower your screen resolution at "display proper ... HP Pavilion F1523 15" LCD Monitor

My monitor stays white it wont show any display


Hi,\015\012\015\012\015\012\015\012This icon indicates the BRIGHTNESS control, more properly called\015\012BLACK LEVEL. It adds or subtracts an offs ... Computer Monitors

No signal on first boot


I think is a power supply problem,, ... Nokia 445 Pro 21" CRT Monitor

Pc wont read monitor


If you look at the monitor there will be an led light on the front that is always orange or yellow when the computer is off but still connected to the monitor. This led will turn green when the computer boots up, sometimes even showing a "no signal" ... HP PAVILION A6230N DESKTOP PC

Wont work with new computer


Since this was a new out of the box computer, Safe Mode was not allowed. In order to change monitor settings (resolution), I had to use another monitor, in this case a newer CRT. With the CRT, the computer booted up, no problem. Once booted, I turned ... Princeton Digital VL173 Monitor

Princeton Digital VL1716 Monitor "No Signal Message"


Roxio Changed Your display settings on the dual display.\015\012\015\012Right Click on desktop>goto Prefences> \015\012\015\012You should see both monitors indentfy the one and change it to a lower resolution. ... Princeton Digital VL1716 17" LCD Monitor
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.7167 seconds