Having problems with your Computer Monitors ?

Envision EN7410e monitor

\015 I had a power failure last night and this morning my monitor lcd light flashes green and does not work. it was plugged into a surge strip and computer boots up fine and a different monitor works fine. is my monitor fried?\015\012\015\012Envision EN-9410e 19" monitor (2005 vintage)Monitor's power light flickers green, monitor will not power up. \015

Answers :

Repair Help & Product Troubleshooting for Computer Monitors

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Envision EN7410e monitor


... Computer Monitors

Envision EN7410e monitor


Just fixed mine. Maybe it's a few years late. Hope you guys still have the display. It's the power supply board. I've just replaced 4 bulge capacitors near one edge of the PS. They are 2x1000uF 10V, 1x470uF 25V & 1x470 10V. I salvaged my parts fr ... Envision EN7410 17" LCD Monitor

No signal to monitor


Have you tried booting into safe mode? If so, do you still get no signal? Also, do you have a video card, or is it on the board? ... HP PAVILION A6230N DESKTOP PC

Envision LCD monitor keeps cycling on and off


Davagain, Your stated symptom leads me to believe that L17LCD2 has a problem in it's power supply/electronic CCFT ballast circuit. The primary cause of the on/off, on/off, being that the SMPS is detecting a fault and then going into SHUTDOWN, trying ... Liquid Video L17LCD2 17" Flat Panel LCD Monitor

I have a Envision EN-7100e monitor. Downloaded


Catamount309, This is only a guess, but unit may have internal "switch-mode-power-supply"/"CCFL inverter" board problem. When screen goes BLACK, is it also BLANK? If you can see WIN-desktop with aid of bright flashlight 1 inch from screen, then SMPS ... Envision EN-7100e 17" Flat Panel LCD Monitor

ISH819 LCD MONITER WITH TFT?


This link, is to the User Manual for the Envision H 819 TFT LCD monitor,http://www.technostation.com/user-guide-owners-manual/Envision/Envision++H819+LCD+MonitorUnder the User Manual heading, you will see ->2009-04-08 12:20:36 ... Envision 19" Widescreen Flat Panel TFT LCD Monitor

Envision Series / AOC 22 hdtv monitor


Probably blown capacitors, the 19" widescreen uses 6 16V 1000uFDo you have a soldering gun? Its not that hard to fix, get the capacitors on ebay for $6-$8 with shipping. ... Envision 19" Widescreen Flat Panel LCD Monitor

We have an Envision 9410e 19" LCD monitor which is about 4 years old. Recently it has started being very slow to start up, especially in the morning after the system is not in use all night. The screen stays black "too long," then it starts flashing, so that the user only sees the images for an instant, alternating with black. After a couple of minutes, the picture kicks in. Sometimes it will do this later during the day, after a break, but not always. / We tried switching the monitor with the o


Cmgusa, Reconnect 9410e to original PC. Please note if same symptom occurs again. This sounds like an intermittant or failed solder connection of some component on the inverter/smps power supply board. Have you tried the FLASHLIGHT test when the moni ... Envision 19" Widescreen Flat Panel LCD Monitor

No Sound on Envision H22W Monitor


The Envision H22W has speaker grilles, but does not include speakers. Note there is no input connector for audio.\015\012\015\012The Envision G22LWK does have built in speakers. I think they just used the same mount/frame for both model ... Computer Monitors

Envision LCD on and off


... Envision EN7410 17" LCD Monitor

''Out of range'' message on an older SVA monitor


This usually means the display resolution settings on your PC are set too high for the monitor to display the signal. Try lowering the resolution on your PC. ... SVA-USA VR 17S 17" Flat Panel LCD Monitor

Envision LCD EN-7100e Monitor "Input not supported


Either your display card is not supporting the LCD resolution. ... Envision EN-7100e 17" Flat Panel LCD Monitor

Remove base completely from envision monitor


After removing all the screws, i used a knife to remove the plastic casing surrounding the monitor. that exposed four screws that when removed, released the base from the monitor. it was just a matter of putting the casing back together. thanks ... Envision 19" Widescreen Flat Panel LCD Monitor

My Envision 7100 Stop Working


These are all some component failure problem in the monitor circuits. This may have been caused by faulty components or overheating of the components causing intermittent or permanent failure of some components in the circuits.This causes the feedbac ... Envision EN-7100e 17" Flat Panel LCD Monitor

Need to Auto Adjust Envision 20" monitor every time


Yes it may be a memory problem inside the monitor replace the memory from technical person \015\012or refer the manual with the monitor some trick may given so that push menu twotimes or operate like mobole button ... Proview PX-986 19" CRT Monitor

Envision EN 5100 E with Dell Inspiron 530...


You can try to reset your display settings... try 640x480 resolution 60Hz refresh rate this can be done in the control panel under display---settings tab..good luck.if that doesn't work I would just return it and ... Envision H170L Monitor

Envision 17" LCD display will not stay on


Seems the N-Channel MOSFET switch in the power supply is the culprit. NTE does not list a replacement part for this, so a sub is necessary (any N-Channel 600V MOSFET in same TO220F case should suffice). I have to look one up for mine. ... Envision EN-7100e 17" Flat Panel LCD Monitor

Color calibration Envision 17" monitor


Return to dealer for service, This is a common problem of a bad backlight on LCD Monitors. If it is on the top comming down it is the top lamp,from bottom up is the bottom lamp. Hope this helps you . ... Envision EN-7100e 17" Flat Panel LCD Monitor

I usually leave my Envision G22LWk LCD on all the time; came into the room today, screen was totally dark (as if "off") but power indicator was lit. Turned monitor off, then back on right away and got a very dim image, esp the top half, for maybe 5 to 10 seconds then entire screen went dark/black again -- can't see any image. again, power indicatorl amp is lit -- monitor is NOT shutting down. so swapped another monitor (old 15" Compaq) which works fine so it's not the video card. tried Envision


Open up the set and look for bad caps, see saome examples of failed monitors here: http://s807.photobucket.com/home/budm/allalbums ... Envision 19" Widescreen Flat Panel TFT LCD Monitor

All pictures appear wider than they really are


You may have to match up the video card settings with the monitor settings to get the correct resolution setting. Try adjusting the resolution of the graphics card to match the setting for the monitor. If this does not work you can call, Envision cus ... Envision 19" Widescreen Flat Panel TFT LCD Monitor

Screen fading to black


Get your monitor repaired by a professional technician. Its due to the picture tube getting bad. these are initial stages, so maybe it can be repaired. Later you'll only have the option to buy one... ... Computer Monitors

Have a hewitt packard computer, want to add on envision monitor 7100s The system is not accepting monitor. what do I do?


To reinerate,do you have the driver for it? I am sure that  the old monitor was made by HP for your HP computer. \015\012\015\012Go to the Envision website and download the LCD driver and install same.    Link provided below ... MPC Computers Envision EN 7100s 17 in. Flat Panel LCD Monitor

OSD locked on ENVISION Monitor


Turn of the monitor then press the menu ... Envision H191W Monitor

Envision LCD i have an envision LCD monitor 17" model EN-7100e one day i restarted my computer and when it came back on i got some lines on top they kinda roled down a bit then its pure white screen. i never had any problems with monitor ever just suddenly screwed up one day hooked up a regular monitor to computer and it works fine


That mean your logic board of the LCD need repaired or replaced. ... Envision EN-7100e 17" Flat Panel LCD Monitor

Envision LCD monitor: ''Auto Config Please Wait'' is always on


Just tell me why this message comes up and if it means my monitor is going ... MPC Computers Envision EN 5100e 15" Flat Panel LCD Monitor
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3172 seconds