Having problems with your ViewSonic VE710b 17" Flat Panel LCD Monitor ?

Power dies when video signal applied

\015 Monitor powers up momentarily and goes to standby normally with no video connected to it, but while its on, it lights up bright white, which does not appear to be a normal mode. Also, sometimes video is fine, but in most cases, the presence of a video signal from the PC's VGA connector to the monitor causes the power to the monitor to shut down completely. It is not going into standby; its going completely off (the power LED is completely dark). The monitor cannot be powered on while connected to the PC's video output, no matter how many times I press the PWR button. Now, if I disconnect the monitor from the PC, it turns on (LED green, white background) then goes to standby. Please note: the PC is NOT the problem, is OK, and works with its usual flat-tube monitor connected. The problem is completely with the ViewSonic VE710b. This is a good one, so please DO let me know if you can help me with this before I give it to my youngest son to tear up!!\015\012\015\012Thanks,\015\012James\015

Answers :

I fixed this problem by replacing all the electrolytics 1000uF and 1500uF on the power supply/inverter board. All were either bulging or had burst at the bottom rubber seal. This cleared up all problems and I am using this monitor successfully at this very moment.
Repair Help & Product Troubleshooting for ViewSonic VE710b 17" Flat Panel LCD Monitor

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Power dies when video signal applied


I fixed this problem by replacing all the electrolytics 1000uF and 1500uF on the power supply/inverter board. All were either bulging or had burst at the bottom rubber seal. This cleared up all problems and I am using this monitor successfully at t ... ViewSonic VE710b 17" Flat Panel LCD Monitor

My monitor will not come on when power is applied automatically. the monitor does not come up when my system comes on. I just replaced the monitor which i swapped same exact monitor, but this one will not boot when the system comes up.


Please work through the following steps to troubleshoot your no power problem with a ViewSonic Monitor:\015\012\015\012Troubleshooting Power Issues: \015\012\015\012Disconnect and securely reconnect ... ViewSonic E70f 17" CRT Monitor

No video signal


That does not sound likely. how old is your computer? if it is more than about 5-6 years, it may have a blown power supply(basically your computer is dead) this happened to my friend's computer while i was there and he blamed it on me, if you think y ... PC Desktops

Acer LCD Monitor only displays "acer" logo


You are correct, it could be a power surge that has caused it.\015\012\015\012Try this..\015\012Unplug the monitor from the wall.\015\012Remove all the video connections at the monitor end.\015\012Wait 10 minutes then pl ... Acer X193W LCD Monitor

3 long beeps and no video plus it doesn't seem to be booting XP


The beep codes varies with the different BIOS manufacturers.\015\012It could be memory problem or the keyboard.\015\012It is not unusal when the power supply blows up that it can damage some of the components in your computer.\015\0 ... Alienware PC Systems ALIENWARE 5620D Notebook

Dead My computer dead when electricity was down. i test power supply to another computer, it works. i put windows xp and install, on the mouse and keyboard stops functioning and fail to command installation.


\015\012\015\012Check your Keyboard-Video-Mouse (KVM) switch. If the system is connected to a monitor, mouse, and keyboard through a Keyboard-Video-Mouse (KVM) switch, or console selector switch, then disc ... IBM NetVista PC Desktop

Monitor powers down upin startup


You need a new video card. it is powering down becuase it is not reciving any signal from you computer. if you are useing onboard video (vga) get a pci video card if you are useing a pci card try puting it in a dfrent slot. ... Gateway 310S (2900621) PC Desktop

Gateway FPD 1830 LCD Monitor


User "noclew1" Your problem is the back lights are not being powered. There is a signal going to your FPD because the power light remains on, but the back lights are what helps support an image from the Front Panel Display.The only way to ... Smart Modular PYXSCAPE SV1170 17" Flat Panel LCD Monitor

I have a kyocera kc 100 viewer and it wont wake up the pc monitor can ya help?


Hi,\015\012\015\012As far as I know, your Sharp screen doesn't have a S-video input. How are you inputting the S-video signal to the screen? The fact that it doesn't "wake up" probably means that it isn't receiving a signal. ... Sharp 17" Monitor

Going to Sleep


Due to the power surge, it is highly possible that the monitor was given a boot by your computer on it's way out.\015\012\015\012This will short out a very small transistor inside the monitor on the video board and in turn, then monitor c ... HP Pavilion F1903 19" Flat Panel LCD Monitor

The screen seems dead


Hi, normally monitors have an indicator light that lites up when power is applied. This changes color or another lites up when it receives video signal from the computer. If no light then most likely defective monitor.\015\012Possibly the only way to ... SGI Silicon Graphics GDM 4011P 20" CRT Monitor

NO SIGNAL What do I do?


These messages are normal when the computer truly goes into suspend mode or loses the video signal (such as when the computer is suddenly turned off).If the monitor displays any of these messages when the computer should be displaying vid ... HP PAVILION A6230N DESKTOP PC

I have a dell demension 4300 that recently started having issues, slow cutain effect, freeze ups. harddrive clicking away. Then one day I had the blue screen that said an error was detected. Then it wouldn't reconize the harddrive but it would go into the bios screen and then not do anything else. So I took it in to have it diagnosed and they said the edie circuit on the board was fried. They offered me a card option for the back but I opted to replace the motherboard with one that was listed as


CaSmogTech,There is a No Signal on the monitor because the monitor is not receiving a Video Signal.Your computer is not producing a video signal.In essence, your computer isn't working, because there is no Operating System on ... Dell Dimension 4300 PC Desktop

Monitor light blinking


Some monitors blink 2 different collers and that means that their is no video signal and some monitors will blink real fast.This is caused by a power cap going bad.If this is happening you need to take appart the monitor and look for a power cap that ... LG Flatron 563LE 15.1" LCD Monitor

When i turn on my computer all it tells me is sva no signal input please check video signal


No Signal. No signal coming from the computer.The monitor is working, but there isn't any video signal coming from the computer.1.Could be a bad video cable. The one from the monitor to the computer. Do you have another ... SVA-USA VR 17S 17" Flat Panel LCD Monitor

Dell Dimension 2400 Powers Up But Doesnt Show Up On Monitor


Seems your new RAM was not compatible but it shouldn't have caused a problem. Use your original RAM - Is it one stick or two? Take one of your original RAM sticks (or the original one if only one) and seat it in a slot - test it. Move it ... Dell Dimension 2400 PC Desktop

No video signal on gt5228, pc isn't booting up properly. The hard drive light doesn't come on, but it runs tried an above board video never gets to pcsetup page. when power is applied the keyboard lights uo then goes off, the hard drive light is yellow then goes out. I disconnected the memory then connected just one memory stick still does same thing. What next


Reset the CMOS ---- unplug the battery off the mother board for 30 seconds and put it back on ... try a new power supply ... Gateway GT5228 PC Desktop

Fan works but no beeps, no video signal. Tried some suggestions.


Sometimes pulling the power cord out of the pc and then replugging it will let it reboot. for some reason these machines die, and they will not reboot until you take all the power off the motherboard for about 10 seconds. ... Gateway GT4016 Desktop PC

My monitor when powered up gives me a no input signal for VGA and DVI and then goes into sleep mode after 15 seconds. I plugged in a second monitor and have a no signal message too. Should i replace the video card or has the monitor locked itself out. Please advise....Best Regards Beth.


Hey BethSounds like you are in a bit of trouble!Based on what you've told me, it looks like it might be a video card fault. However, a few things to check first are..Make sure the VGA & DVI are secured tightly ... HP f2105 21" LCD Monitor

Computer dies on me (can't say it better due to no technical knowledge; pls read :-)


The 'click' sound you hear when your computer goes off is the hard drive head parking itself.  It does this whenever the machine shuts down to prevent damage.As for the problem itself, I believe your computer is overheating.  Th ... Acer TravelMate 290LCi Notebook

No video signal to Monitor.


Lack of video signal is usually 1 of 3 things, Power supply (PSU), Video card or Motherboard (mobo).Situation #1: If you get a blank screen and no sounds or movement it either indicates that the power supply unit (PSU) has failed or something o ... E-Machines eMachines Desktop PC

I recently moved my computer into my new condo and have not been able to use it since. The problem seems to be with the monitor. I turn on the computer and the fan comes on but the monitor displays "no signal" and then goes dark but the light one the front still flashes indicating it is getting power. The last time I moved my computer from one room to another, the monitor suddenly couldn't/wouldn't display colors accruately - no red. Attempt to adjust the color by using the monitor's controls we


Lack of video signal is usually 1 of 3 things, Power supply (PSU), Video card or Motherboard (mobo).Situation #1: If you get a blank screen and no sounds or movement it either indicates that the power supply unit (PSU) has failed or somet ... E-Machines eMachines Desktop PC

Hello Sony RB30 w/ sdm-hx93 monitor. Approx. 7


Blond and Baffled, (CD), it's okay, I believe you have a common problem.The computer sends a video signal to the monitor. The monitor is working fine. Hence - No Signal.Monitor doesn't receive a video signal within a certain s ... Sony VAIO RB30C (VGCRB30) PC Desktop

Mag Innovison LT917S LCD Monitor


After looking at the description of the pin outs on the BIT3193 and following signals to/from that chip I discovered I had burned up one of the FETS that I had installed. With the FETS replaced for the second time the monitor works fine now. HEY!! ... Gateway FPD2275W LCD Monitor

No display (black) - power light is amber color


The video signal is not reaching your monitor, check the pins on the connector from the monitor to the computer, then check the video card: \015\012\015\012Turn off your computer, unplg the power, and then take out the video card. Wait ... ViewSonic VX910 19" LCD Monitor
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.6642 seconds