Having problems with your Sony VAIO VGC-RC110G (VGCR110G) PC Desktop ?

Monitor reads no signal...

\015 I turn on my Sony Viao VGC-110g and i dont get anything!! No beeps or anything. It was a monitor issue at first. Now im not sure what it could be.I get the power light, media check and thats it. Black screen thru the whole process. The porblem b4 was I couldnt use dell or lcd monitors, but only old cheap crt's. please help me... Took it in and they say i need a mobo..Say it aint so!\015

Answers :

Its not mobo...since it power up and you see the light indicator are processing ..to be sure ..when you turn on the pc..does the light for HDD is processing like blinking green/blue..if does..try to connect your monitor to other computer..if your monitor works..thats good..

if your video card is built in to mother board..the cause is one of the pin of the port is disconnected..you cannot fix this..but you can replace the video card by installing it to one of the expansion slot inside the computer...check what kind of interface for video card slot inside the computer (PCI, AGP,PCI express)..then buy that and install it. its plug and play

good luck
Repair Help & Product Troubleshooting for Sony VAIO VGC-RC110G (VGCR110G) PC Desktop

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Problem with the monitor


Hi,The three boxes represent the built-in diagnostics of the monitor. The letters G is green, B is blue and R is for red, the 3 color guns of the picture tube of your monitor. The words "Self Test" indicates that it is in diagnostic mode ... Compaq FS7550 17" CRT Monitor

No color red displays.


If you think that electronic repair is very difficult to learn then you have to read this article where only by using a solder gun could solve a Monitor color problem. Of course there were many tough dog cases (very difficult to find out the fault) i ... ViewSonic G70fmb (Black) 17" CRT Monitor

We are getting a No Signal on our monitor,


I have a Acer Aspire M1202 and got the no signal on the monitor it was the power supply. My was a short in OEM power supply unit. ... Acer Aspire L100 PC Desktop

Inout signal out of range Answer Failed: retry


It shows out of range because the PC is sending out the video signal that is higher than the monitor can display, you need to set the PC video resolution to the native resolution: 1024 x 768 @60Hz. You can reboot the PC into save mode (hitting F8 key ... IBM ThinkVision L151 15" LCD Monitor

My monitor ( with less that 6 months use) has been going off while someone is using it--- says out of signal and i have to restart the comouter... and this is not stopping even with a restart


Julezj, You will need to connect your monitor to a KNOWN GOOD pc that DOES NOT have the screen saver set to do a time out when the keyboard is inactive. Whenever you state a problem with a monitor on fixya, please mention the monitor technology you a ... Gateway Computer Monitors

Acer Model AL1916W A reads no signal after being on for 1 hr


The problem seems to be that the computer, do not recognize “which monitor’s connected?” Follow these steps to correct the problem: Shutdown the monitor, next shutdown th ... Acer AL1916W 19" LCD Monitor

No signal The TV stopped showing a program and on the screen it read, "no signal". In the household there are two other TVs that operate OK. This is a cable TV setup. Checked the cables and they are all connected firmly


This problem requires you to test both the monitor and the signal input form you cable tv setup. Set the monitor up on a computer and see if it works properly. If it does then you may have a problem with the signal conversion of the cable tv to the ... Envision 19" Widescreen Flat Panel LCD Monitor

"No signal detected" when LCD connected with DVI-D Cable


Thank you for providing your configuration details.\015\012You have failed to specify wheather or not your LCD Display is under Warrenty.\015\012\015\012Perhaps these simple trouble shooting procedures will get the job done.\0 ... BenQ FP71E 17" LCD Monitor

Emonster 600 won't boot up


You should not loose any information seeing that all information is held on your hard drive. As for changing out the processor, it seems pretty intimidating but is rather simple. When you have the side of the computer removed and can see into th ... AMD eMachines Desktop System w/ 17'' CRT Display, 2.0 GHz Athlon 64 3000+ (W3400)

No display on SyncMaster 710N


I used 2 resistor of 100 ohms (1/8W) to make one of 50 ohms. Like others instruction, just put the 50 ohms resistor between pins 5 and 6 of this chip and the problem is solved. ... Samsung SyncMaster 710N 17" LCD Monitor

An Out of range box


Frankr2327\015\012\015\012If you are getting this message this means that you are connecting a device to the monitor and/or a connection that is putting out a signal that is not supported but the monitor. You may also need to look at the ... Envision Computer Monitors

Gateway 900g Hi I have a Gateway 900g monitor that does not work. All was fine working until one day it just stopped working. It wont switch on or anything. I think it may be the power supply board but I cant seem to find one anywhere and I read that you fix them. If so then how much would that cost and how do I go about it. Regards Adrian


I'm writing this using a recently repaired Gateway 900g. You may be correct about the power supply, as that was the problem on this unit. There was absolutely no response with this unit. No blue LED, no dim display. Nothing.\015\012\0 ... Microsoft ChiMei CMV938D 19" Widescreen LCD Monitor

Signal degradation across vertical section of


This appears to be a common complaint on LCD monitors. Some LCD screens have control issues.An LCD screen is the panel and a bunch of Line control chips wrapped around the outer edge. A problem with one line top to bottom or left to right is al ... iiyama Computer Monitors

No signal to monitor. all cords are tight, and plugged in. no beeps when computer starts up. Can't test anything nothing shows on screen. Tried it on another computer, worked fine. amber light below g


Check the connection which links the CPU and the monitor. Also check the power cable of th3e monitor\015\012\015\012Thanks\015\012Nilesh ... Generic Memory Compaq Presario SR1215CL by HP AMD Sempron 3000+ 512MB 120GB CDRW/DVD w/XP [Refurb] [MIN90] PJ506AA... (PJ506AAR) PC Desktop

ViewSonic VX922 monitor - black screen - green power light flashes


PLEASE read Carefully so here is a fix for the green blinking light ...the monitor is going into shutdown....protect mode......THIS is ...Only for the seasoned electronic service tech ......YOU NEED TO BE into Electronics ..or have electronic backgro ... ViewSonic VX922 19" Monitor Flat Panel

One monitor clear the other not good fonts


I installed a better video card that supported dual monitors without splitting the signal. ... Advueu Technology ADV178T 17" Flat Panel LCD Monitor

Screen black, will flash on for a second if you put


Ktoll, Wow you will need to do a lot of surfing and a ton of reading to educate yourself as to why your monitor has the BLACK SCREEN OF DEATH!! Yes, you too, with some research might possibly fix your own monitor if you know how to use a soldering i ... Computer Monitors

My monitor blureed


Both suggestions are good starting points, but it may be an internal fault.Other steps to try: check the signal cable -- wiggle it a bit at the PC end and at the monitor end, while watching the image on the monitor. Any change? If you ha ... ViewSonic A90f+ 19" CRT Monitor

Signal out of range


1: Signal out of range meas the monitor can't handle the input refresh rate. lcd and Tft monitors usually supports 60 and 75Hz refresh rates.2: The Resolution you are using to view the desktop is too high, this number is depending on the size o ... Kogi L7CH Monitor

Desktop has no signal


That means that the input from the monitor has no read able signal\015\012Either the monitor is bad or the onboard or video card\015\012Take the monitor and hook it up to a different PC to see if it works or hook a different monitor into ... HP Pavilion 533w (P9859AR#ABA) PC Desktop

Compaq Presario SR1000 desktop boot up problem


Hello jjissaved55,It appears as if the motherboard itself, is the problem as you have ruled out monitor and your having multiple problems (HDD, monitor, keyboard).If it was the processor you would not be having problems with t ... PC Desktops

I have a dell inspiron 9300 with win xp pro for an os, my lcd screen is broke, so i took it off completly. now i am trying to hook up an benq fp567s monitor through the vga output. it will get me as far as desktop screen just after boot up. & most of the time it goes in to sleep mode before start up is complete. the screen suddenly displays "no signal" ?


Many people have noted two primary failures with this monitor. i have a couple time-saving troubleshooting tips, which actually apply to mostly all electronic devices. first, of course, bulging electrolytics [capacitors] should be considered suspect. ... BenQ FP567s 15" LCD Monitor

I have a HP Pavilion laptop ze4900. Every time I move th screen, the display either goes off completely, or it goes vey dim and I cannot read anything from it. The only thing I can do to get a display


You could have a defective screen - a defective inverter or a CCFL lamp.To determine if you have a LCD screen or video card problem, read this and follow the instructions.Defective CCFL backlight, it may have the following symptom: ... PC Desktops

Cannot read the model number (chinese) I known i have a flat screen monitor 20 inches from DELL 2004 I want to connect it to my Inspiron 1100 .I need instructions this an handme down so I have no manual.The monitor does not connect automaticly.I have a blue end plug on the inspiron with 15 pins the cable connect to the monitor with another 15 pins=15 pins at both ends. The monitor connect to a power pack connected to an outlet. (is there something missing ?) The monitor display 1:D-SUB & 2:DVI-D


Since the cable you're describing is a VGA cable with the 3-row, 15-pin configuration, it will be the 1:D-sub selection. The DVI choice is for HD TV or a display card with HD capability. The S-Video is more commonly used for higher clarity video sign ... Dell Computer Monitors

Building a new PC, cannot get LCD to work


You MUST get into bios to set "initalise display first"selection.\015\012try alternatly pressing delete,or f1 keys toget into bios.\015\012one of the two will get you "in"\015\012\015\012then follow instructions at bottom of s ... E-Machines eMachines T3830 PC Desktop
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.4088 seconds