Having problems with your Sceptre X7GNAGAV 17" LCD Monitor ?

Sceptre 20" Monitor will not stay on

\015 I bought my Sceptre 20" monitor in 2003 from Tiger Direct. It worked fine until about 2 weeks ago. When I turn on the computer and screen the screen will not stay on.I initially had to keep pressing the on screen button about 20 times, and in the few seconds it was on keep trying to get the internet to come up and then email, now I am up to about 50-60 restarts for the "on" button. It seems to stay on after about 50 starts but only if I can get the internet going,especially email. I tried setting the standby timing, used the screen controls but nothing is working.Once it stays on it will keep on unless I am not actively using it, if I am away from the computer more than a minute it shuts off and I have to start all over again! I am not a geek, should I junk this?\015

Answers :

First check the monitor sleep mode for your monitor in windows control panel, check that its not going into hibernation/stanby. if thats not it. and the monitor keeps shutting down. You may have to replace it newer models have more features and could be cheaper by saving you the hassel check newegg.com or orverstock.com
Repair Help & Product Troubleshooting for Sceptre X7GNAGAV 17" LCD Monitor

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Sceptre 20" Monitor will not stay on


First check the monitor sleep mode for your monitor in windows control panel, check that its not going into hibernation/stanby. if thats not it. and the monitor keeps shutting down. You may have to replace it newer models have more features and could ... Sceptre X7GNAGAV 17" LCD Monitor

Sceptre X20G Naga II 20.1" Widescreen monitor


I am working on one of these for a customer. Found leaky cap on 5 volt power supply. replaced it, still no backlight. Looked at the inverter with an o-scope and it runs for a few seconds then shuts off. I hooked a ccfl across each of the transformer ... Sceptre X20G-Naga II 20.1" Flat Panel LCD Monitor

When I turn on my Sceptre monitor it stays on for a few seconds


This seems to be a comman fault with alot of monitors, the problem is caused by faulty componants on the power board called capacitors.If you have soldering skills and a bit electronic knowledge its an easy repair and one that you could t ... Sceptre Computer Monitors

Monitor stays on for a few seconds then goes out


This problem is very often caused by dry electrolytic capacitors on the inverter board. If you have some skill with soldering you could try to change them. When buying new ones ask for LOW-ESR capacitors for switching mode power supplies (SMPS) and 1 ... Acer AL1711 17" Flat Panel LCD Monitor

22" Sceptre LCD monitor DVI to HDMI problems.


... Sceptre X22HG-Naga Monitor

I have a 20 sceptre widescreen lcd monitor


Have you tried any other monitor connected to your computer since your current problem? Check your connections, make sure your VGA cable/DVI cable are in good condition. If none of that works try to RMA it to sceptre if your still within the 1 year ... Sceptre X20g-Naga III 20.1" LCD Monitor

Sceptre X9G Komodo IV 19" Monitor


Sceptre X9G Komodo IV 19" Monitor?\012 This trouble maybe power supply or inverter boards is defective.\012 first you can test the voltage of the multr,and then check which part is defective.From Wisiny.com can find those parts\012 if you hav ... Sceptre X9G Komodo IV 19" Flat Panel LCD Monitor

At start-up, Sceptre X7 monitor flashes on, then goes black. Must turn computer on and off numerous time before monitor will stay on. How can this be fixed?


I just found after hooking one of these Sceptres with the exact same problem up to a computer that already had a lcd hooked up and the computers settings were fine that if you go to the MONITORS menue and change the MONITORS time setting from 15 seco ... Sceptre X7G-Naga 17" LCD Monitor

Monitor Powers off after a second or two.........


My Sceptre Xg5 Komodo just stays on for a second or two and then goes black.......Displays accurately for that amount of time. Cut it off and back on......Same thing. LED indicator is on when it goes out. Any Ideas?? \012 This trouble maybe power sup ... Sceptre X5G-Komodo IV 15" Flat Panel LCD Monitor

The power light blinks solid blue every four seconds or so (it?s off in-between). The screen is blank. None of the buttons on the side function (such as ?menu?). I have a second similar monitor from the computer in the other room I?m using to type this proving the video card and cable are fine. We?ve always (as in years) left the monitor on (w/ a screen saver) but for whatever reason turned it off for four days when we went away recently. The monitor would then not turn back on. After leaving th


Hello,\015\012Two days ago I received a Gateway 900w FDP1975W Monitor from a friend. He told me that he would have to let it rest and it would work for about a hour or so and flash green with lines, then Flashing blue power light, then nothing. ... Gateway FPD1975W 19" LCD Monitor

Same problem here


Same problem here?\012 This trouble maybe power supply or inverter boards is defective.\012 first you can test the voltage of the multr,and then check which part is defective.From Wisiny.com can find those parts\012 if you have any question,p ... Sceptre X9G Komodo IV 19" Flat Panel LCD Monitor

Sceptre LCD - no display


It may be the capacitors, since capacitors run about $1.50 or so depending on size you may spend a little over $6 total if you already have soldering equipment or a friend with skills. ... Computer Monitors

X20G-Naga III screen goes blank after 1-2 secs


FIXED!Device : Spectra X20WG-NagaProblem : monitor comes on then flickers then goes offsolution: Replace Capacitor C101 (150uf, 35V) and Fets U101 and U102 (4511GM)Comments: This is a common problem with this monitor. ... Sceptre X20g-Naga III 20.1" LCD Monitor

Monitor Goes Black


... ViewSonic VP191b 19" LCD Monitor

Monitor stays black until boot up to Desktop


You use a graphics card as your main output?and you have onboard graphics output too that you dont use?if so then you will have to plug your monitor lead into the onboard output socket to see bios. i think you need to go into bios and cha ... Sceptre X9G-NagaIV 19" LCD Monitor

X20G-Naga III screen goes blank after 1-2 secs


Most common lcd monitor break down, check all electrolytic capacitors for leakage and loose board solder specially on the ccfl inverter section. ... Sceptre X20g-Naga III 20.1" LCD Monitor

I have a sceptre x9g-naga III


Not an expert, but from what Ive read, this is a cfl inverter issue. I had the same problem on my Sceptre. Good luck finding parts. My solution: get another monitor. ... Sceptre X9G-NagaIV 19" LCD Monitor

Sceptre monitor just wondering what capacitor was the one you replaced for the monitor. mine stays on for 2 seconds then shuts off.


I would suggest looking at the capacitors on the power supply board. I just got one today with 3 blown caps (the tops are swollen) and a couple missing components.The ones blown on mine are the 220uF @ 25V and 1000uF @ 16V. ... Sceptre X9G-NagaIV 19" LCD Monitor

Sceptre S1902D LCD 19" Monitor... When initially powered up, the screen is on for about a sec or two, then goes black. If I turn the monitor on and off quickly, it usually comes on and stays on after the 4th or 5th attempt. Is this indicative of a bad inverter board or bad fluorescent backlights? Thanx


Good wholesale price fluorescent board. ... Sceptre S1902D 19" LCD Monitor

Keeps blinking out to a black screen


Hi,If the power light stays on and the unit works even if for just a moment, then chances are that you either have a cold solder, or a heat problem with some components or your CCF Lamp is starting to fail.All possibilities re ... Computer Monitors

Screen Not Staying On


Hi TontBrowne,\015\012\015\012I'm not sure exactly what causes this problem. However it seems that lowering the 'Brightness' and 'Contrast' fixes things. The problem is, you can't see the menu without the backlight. However, try this, as ... Dell Dimension 4600 PC Desktop

Sceptre X7, 17'' monitor blue light comes on at initial start up, however no picture, move mouse and pictures is up and then goes black. If I turn it off and back on the picture is only briefly there. After repeating on/off 8-10 times the picture stays.


... Computer Monitors

Sceptre x9g-nagaV monitor only stays on for a second and shuts off...power light shows stand by....replaced all small capacitors except 100mfd 400v value shows good on that one ,checked over solder joints....went to remove a bipolar transistor to check and broke the leads...anyone know what a substitute might be...the numbers on the case are A7431,BZAE1,526BD...i'm an amateur at this but trying to fix just for grins....thanks for any help


... Sceptre X9G-NagaIV 19" LCD Monitor

X20 Naga II 20.1" Widescreen


... Sceptre X20G-Naga II 20.1" Flat Panel LCD Monitor

Sceptre display needs warm time to up stay stable. After about one min it is OK


Grier_r, If unit is a LCD type and has fluorescent lamps supplying WHITE light so you can see all the pretty colors on the screen, you should NOT need to WAIT more than 2 to 3 seconds for unit to come "ON". IT needs to be investiated by a Electronic ... Computer Monitors
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3181 seconds