Having problems with your Sceptre x22wg Gamer Monitor ?

Openin case for sceptre monitor to try and fix (no screws?


Answers :

The only tools you'll need to open up the X22's case are your hands and something like a plastic putty knife. First use your hands to pry the face plate away from the housing along one of the four sides, that is, working from the middle where resistance is lowest. After you create a gap, insert the the edge of the putty knife and forcibly slide it toward one of the corners. This will separate that portion of the face plate. Do the same for the second corner. Now one side is free. Do the same for the other three sides. After you remove the face plate you'll see 4 screws that pin the lcd panel to the housing. After you remove them, be careful not to allow too much force to pull on the cable assembly that connects the panel to the mobo. Just reach in and squeeze the little metal clamps that fasten the connector to the panel. Do not try to disconnect it from the mobo from this angle. Disconnect it from the panel. Good luck.
Tom Raywood
Repair Help & Product Troubleshooting for Sceptre x22wg Gamer Monitor

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Openin case for sceptre monitor to try and fix (no screws?


The only tools you'll need to open up the X22's case are your hands and something like a plastic putty knife. First use your hands to pry the face plate away from the housing along one of the four sides, that is, working from the middle where resista ... Sceptre x22wg Gamer Monitor

Can't set up network w linksys modem


Video card:Your computer has an integrated video card but has a "PCI Express" expansion slot for an upgrade. After the upgrade you will be able to play most games without the choppy frame rate...depending on what card you buy. Since ... PC Desktops

LG Flatron L1932TQ won't turn on


I have the exact same problem. Just like Ptepe, I also found the 680uf/25v and 1000uf/16v capacitors in positions c203 and c204 on the Power Supply PCB to be bulging on the top. I considered replacing all of the electrolytic capacitors on the board, ... Gateway FPD2275W LCD Monitor

No connection from cpu to screen.


By working fine, I assume you mean the monitor goes into its test/diagnostic displays. If that is the case, most likely your roommate has hit upon more or less the correct deduction. Two possibilites should be attempted before assuming to much ... Compaq Presario 7594 PC Desktop

Monitor displays breifly then goes to blank screen


Well my Acer AL1711 finally gave up in as much as the screen flashed briefly at switch-on then went blank, regardless of brilliance setting so I decided to take it apart and try to fix it. The good news is that IT WAS NOT THE LAMPS that I feared in m ... Relisys RLT1720 17" LCD Monitor

PC issues I have a Medion M3 Compressor 5200 PC desktop. When I try to turn on the computer, I hear the fans start but the keyboard doesn't work and the monitor says : Self Test, Check your PC and Signal Cable, Monitor is working. I'm not sure what the problem is and I don't know how to open the CPU case to check or fix any problems. Any help is much appreciated. Thank you.


Do any of the lights on the keyboard light up, even for a second? Your monitor is probably working right, but I would unplug both the power and video cables from the monitor & pc and re-plug them, then turn it on and see what happens. Also, you ... Medion M3 Composer 5200 PC Desktop

How to open casing


Just managed to open a FP17G+ monitor. My hope is that FP17G is similar and that this comes in handy.\015\012\015\012There are 5 screws holding the casing together. Four are in the corners (black screws on my monitor). The 5th is right un ... BenQ FP71G 17" LCD Monitor

Screen goes black


This problem is fixable with no parts.\015\012the ribbon cable inside the back of the monitor most likely is loose.\015\012if when the screen goes black you can tell that the back light is still on inside the screen then this fix is definitely ... HP Compaq nx5000 Notebook

Hp pavilion f1930 shows pic for 2 secs. then blank


Rather than guessing, or blaming the computer, I fix the F1903 backlight problem. Power the monitor and using a bright flashlight check the screen to ensure there's an image, or the menu when you press the menu button. Nearly every one of the F1703 a ... HP Pavilion F1903 19" Flat Panel LCD Monitor

Optiquest Q9 After about 14 months, my 19" LCD Optiquest Q9 monitor suddenly got very dark ( the bottom 1/4 was still viewable, though dark) and then went blank. After it cools for a while I can power it back up with the same results. There is a faint click when it goes black. I have replaced it with another 19" LCD ( different MFG.) which is working fine, but hate to throw this one away if it is repairable. The screen itself seems fine with no pixels missing at the time it went dark. There are


I had this problem with my Q9 and I was glad to find the FixYa website with help. But I will offer more detailed info for novices to make sure you find the capacitors. First of all, it is not easy trying to find out how to open the monitor up! First, ... ViewSonic Optiquest Q9b 19" Flat Panel LCD Monitor

Problem on hp monitor


I have a Dell E171FPB monitor that had the \015\012same problem with the Main Menu coming up and I thought I would tell you \015\012what I did to fix the problem.\015\012\015\012\015\012\015\0121. I shut down the PC.\015\012\015\01 ... HP vs15 15"LCD Flat Panel Monitor

Relisys 17in tft monitor


Hi everyone, i have a relisys monitor and had this exact same problem where the menu screen comes on and then cycles through the various options until it gets stuck in a loop within the colours settings. - the solution i found ... Relisys TL 766 Monitor

How to remove stand from iiyama E2607WDS monitor


One can only remove the plastic neck of the stand by removing not only its four visible screws, but also the two screws at the invisible inside of the neck. To get to these, you have to remove the neck together with its metal foot. To do so, you shou ... iiyama Computer Monitors

HDMI/DVI input problems


You could try opening the housing, with the power cord unplugged. Find the location on the circuit board where the HDMI/DVI port interface with the circuit card. Check the condition of the solder joints and look for signs of a cold joint or bad conne ... Gateway FPD2275W LCD Monitor

Acer 3680 needs several days rest before restarting.


Hi George,If you power on with an external monitor connected, no function-F5 is necessary - it will default to the external monitor automatically.I don't think Darkman is on the right path here (sorry Darkman). It is possible, ... Acer Aspire 3680 Laptop

The brightness/contrast adjustment screen pops up randomly and often. It then scrolls through the 3 options and the only way to remove it is to turn off the monitor. How do I make it stop?


Sounds like your buttons are stuck. Try loosening them up by pressing them, then popping them out again with some sort of pin or needle.If all your buttons seem fine and pop in and out normally, then its probably a problem with the connec ... Dell Computer Monitors

Philips 190S monitor - Urgent!


The lcd has three parts the screen plate(windows)/the logic(vga)/the inverter(power plug). Parts that go are the backlight ccfl's, behind the plate, and parts of the inverter, ie capacitors, all three take a bit of power from the inverter. The self t ... Philips 190P6EB 19" LCD Monitor

Gateway MD2614u screen stays black when powered on. No beeps.


Hi!Follow these methods, each one at a time, to try fixing your problem:A)\015\012 Unplug the power cord from the ;aptop and remove the battery as well. Press the power button (yes, without any electricity source connected!) s ... Gateway M305CRV Notebook

Samsung 931 B - Dual monitor setup. one monitor no longer shows anything - LED is blinking about once every 0.75 seconds. either power cord or either source cable works with other 931B, but broken one shows nothing on screen, ever. screen actually blinks SLIGHTLY at same interval as LED. not using DVI cable- using old school rgb on each. i need two identical monitors. fix this one (myself or professionally) or get new one?


The caps (capacitors) in the powerboard are going out. This is a very common problem in all class and price ranges of modern lcd and plasma tv's/ monitor's. I don't know if this problem has been like this for awhile or it just started, but either way ... Samsung SyncMaster 931B 19" LCD Monitor

Problem on hp monitor


I know you said there were others that had the \015\012same problem with the Main Menu coming up and I thought I would tell you \015\012what I did to fix the problem.\015\012\015\0121. I shut down the PC.\015\0122. I removed the p ... HP Pavilion F1523 15" LCD Monitor

Main menu / positioning /


I have a Dell E171FPB monitor that had the \015\012same problem with the Main Menu coming up and I thought I would tell you \015\012what I did to fix the problem.\015\012\015\012\015\012\015\0121. I shut down the PC.\015\012\015\01 ... Dell E151FP 15" Flat Panel LCD Monitor

Display panel on dv9040us has opened up


Could you post a picture of your problem? The issue is probably that the screws holding the monitor mount to the rotating piece have stripped and come out, and the small piece that is meant to stay screwed in is spinning freely. This can spread tha ... PC Laptops

ViewSonc VX924 LCD Monitor


Check the information at Viewsonic's website regarding their warranty:http://www.viewsonic.com/support/warranties/limited-warranty/If you have your proof-of-purchase and it shows the monitor is less than a year old, it would b ... ViewSonic VX910 19" LCD Monitor

Input select screen is poping out by itself and anoying me.


One of two things:1) The input button is stuck and is staying pressed down, making the input select screen pop-up, in which case I would suggest wiggling it and making it un-stuck (Thats the technical term by the way :) ).OR ... BenQ FP931 19" LCD Monitor

My monitor shuts off(goes blank for a few seconds


The monitor is doing a self test a finding an error.The lcd has three parts, the screen plate(windows)/the logic(vga)/the inverter(power plug). Parts that go are the backlight ccfl's, behind the plate, and parts of the inverter, ie capacitors, ... LG L1915S 19" LCD Monitor
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 1.0277 seconds