Having problems with your Sceptre DCL9a ?

How to turn off burn-in mode if botton on Monitor

\015 I am trying follow the steps below, I can't turn the monitor off because the powerbutton would not response, so I pull the monitor power plug off, then try to follow steps again, nothing happen. Please help!\015\012\015\012Turn the monitor off* Hold down the Menu button and the plus button* While holding the other two down, press the power button. Wait for the DVI connector graphic to disappear* Release all buttons* Press the minus button. The Service Menu should appear* Scroll down to Burnin Mode using the minus button* Press the Menu button to activate that setting* Press the minus button to set it to Off (it should be blue when selected)* Press the plus button to highlight Exit Menu* Press the Menu button\015\012\015\012After over 6months of the computer been turned off(split up and had to move out) I recently reconected it. The computer seems to boot up ok but I have nothing on my screen. Now this blue box with "BURN IN MODE" has appeared. I can't get rid and can't use my comp. :-(\015

Answers :

I didn't have the monitor connected to the computer, and that's why the power button was unresponsive. After connecting it, the solution above worked for me.(My KVM switch was set to a computer that was turned off)
Got monitor out of burn in mode by unplugging the power to monitor then while holding down the power button on monitor plugged in the power cord to the monitor all while it was connected to a running computer. Was able to turn the monitor off with the power button. When I pressed the power again the burn in mode was gone and the monitor was displaying what was on the laptop computer.
Repair Help & Product Troubleshooting for Sceptre DCL9a

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to turn off burn-in mode if botton on Monitor


I didn't have the monitor connected to the computer, and that's why the power button was unresponsive. After connecting it, the solution above worked for me.(My KVM switch was set to a computer that was turned off) ... Sceptre DCL9a

How to turn off burn-in mode if botton on Monitor


... Dell E176FP 17" LCD Monitor

Benq monitor flashes primary colours when switch on or off


This is called burn-in mode. Used to test the monitor at the factory.\015\012To fix this, use the buttons under the front of the monitor,\015\012There are six buttons. Let's number them 1 to 6 from the left.\015\012Press 6 to displa ... BenQ FP71E 17" LCD Monitor

No picture on monitor 997M


One reason that this is happening could be that it is on Power saving mode. This happens when the LCD monitor detecs an incorrect timing then thats the time that the LCD goes blank and the power botton starts to blink.\015\012\015\012what ... Microtech Computer Monitors

My monitor is stuck in burn in mode and i cant


... Sceptre DCL9a

Switching to "off mode"


You are making the assumption that I have two monitors! If I had two monitors, I would be looking for a fix, I'd burn the other one. ... Hyundai ImageQuest V995 19" CRT Monitor

Dell monitor flashing different colours and buttons won't work!


Go into your monitors settings and select "Factory Reset" Then go to "Factory" and you will find the burn in setting. Turn burn in to off. This should fix the problem. ... Dell E176FP 17" LCD Monitor

Monitor will not turn on- was working fine a week ago!


Hi this is the way how to examine\015\012what's wrong with your LCD monitors. After you turned it on and the screen\015\012went gray or stopped working, you have to check that if you can see the image on the screen or\015\012not by shining a fl ... Gateway FPD1960 19" Flat Panel LCD Monitor

Digital power saving mode


Check your monitor power settings.right click on your desk top then left click on 'properties' in the white box that appears.this will bring up a 'display properties' box which should have a tab headed 'screen saver' amongst o ... Gateway FPD2275W LCD Monitor

Monitor Mag innovision 796PF. 30% more Black screen


This sounds more to me like you are experiencing problem with your video adapter than the monitor itself. Have you tried a different video card? If you have onboard graphics, you may have to disable it in BIOS inorder to install a new graphics card ... PC Desktops

Hp vs17e monitor says it's in sleep mode then goes blank


If you are running Windows Vista,do the following,\015\012\015\012\015\012Click start,Control panel,\015\012Double click Power options,\015\012On the left menu bar,Click Cha ... HP Vs17 17" LCD Flat Panel Monitor

Dell P1110 This thing works great...but...whenever I shut it down, and then try to turn it on again later, I have nothing on the screen (color bars) and the LED continues to blink green, until about 10 minutes later, it magically come back on...I?ve tried to find some info like when I hade the brightness problem, but I have not had any luck. Pleas help!


Using the buttons on your monitor, see if there is a "burn in mode" or "self test mode", and turn it off via the monitors other buttons. (not the power switch) ... Dell UltraScan P1110 21" CRT Monitor

Burn in Mode displaying on Monitor


Check the RAM ... Dell E176FP 17" LCD Monitor

Proview 900 series black flat panel monitor


Its sound you have bad inverter chip. The I.C. "BIT3193G" is the main controller in the inverter circuit. This chips is a surface mount chip and you must be careful remove it or you can damage the board. Also have you check for any burn out transisto ... Computer Monitors

Monitor turning black


The backlight fluorescent bulb is burned out. ... Computer Monitors

My monitor randomly turns off.


Most likely you have a bad INVERTER BOARD.\015\012\015\0122nd in line is a burned out backlight fluorescent bulb. ... E-Machines E17T4 LCD Monitor

Analog Power Saving Mode


Right click on your desktop>Properties, then click on Screen saver tab, then at botton of the box you should see 'Monitor Power'.\015\012\015\012Click on 'Power' then Power schemes tab.\015\012\015\012Look at 'Turn off monitor' and set to 'Never' ... LG Flatron L1951S-SN 19" LCD Flat Panel Monitor

My lenovo Y510 ideapad turns on but the screen remains black. All of the buttons light up, but the screen stays like it is in sleep mode. I have tried rebooting, removing the battery but nothing seems to help. Any ideas?


The next tim eit is turned on, try shiniing a bright flashlight directly on the screen. If you can see anything there then the backlight has burned out on the screen, and will need to be replaced. If you cant see anything, ... Lenovo IdeaPad Y510 Notebook

I was on my computer and I was on the internet. Then the computer screen turned into a creme colored screen with vertical lines going down the screen. I cannot exit out of the screen or restart the computer.


1. if your computer is locked up.. try to force a shutdown by pressing the power botton on your tower and holding the bottom pressed until the computer powers down. wait 15 seconds then try to restart again.\015\012\015\012if your monitor ... PC Desktops

Samsung syncmaster 711p power issue


Hello\015\012I am a technician-informatic. I have repaired about 80 Lcd Samsung monitors with theese problems. I offer the repair manual.Manual has been done with the experience of the repairing Samsung Lcd monitors. Manual was made by m ... Samsung SyncMaster 931B 19" LCD Monitor

NO SIGNAL What do I do?


These messages are normal when the computer truly goes into suspend mode or loses the video signal (such as when the computer is suddenly turned off).If the monitor displays any of these messages when the computer should be displaying vid ... HP PAVILION A6230N DESKTOP PC

New Samsung monitor returns only a blank screen when turned on. what can I do?


Hello\015\012I am a technician-informatic. I have repaired about 80 Lcd Samsung monitors with theese problems. I offer the repair manual.Manual has been done with the experience of the repairing Samsung Lcd monitors. Manual was made by m ... Samsung SyncMaster 910MP 19" LCD Monitor

My Samsung LCD TV/Computer Monitor just went deadOnly 14pins/15


It sounds to me like the monitor/TV needs to either be replaced or sent in for repair but there are a few things we can test. \015\012\015\012The first thing would be to set the TV to connect a cable line to the TV and see if you can get ... Samsung SyncMaster 204B 20.1" LCD Monitor

Blank screen i have 3 samsung 740B 17" monitors its been 2 years and i have 2 down,both source buttons light up telling me power is good.ive tried different monitor with the same cpu and it works fine. i have 7 work stations at my work 4 have dell monitors running for 5 years +, and 3 are samsung,which i only have 1 left working now. only had them for 2 years. just woundering if theres anything i can try or are they garbage?


Hello\015\012I am a technician-informatic. I have repaired about 80 Lcd Samsung monitors with theese problems. I offer the repair manual.Manual has been done with the experience of the repairing Samsung Lcd monitors. Manual was made by m ... Samsung SyncMaster 740b 17" LCD Monitor

Monitor is going out...


Hello\015\012I am a technician-informatic. I have repaired about 80 Lcd Samsung monitors with theese problems. I offer the repair manual.Manual has been done with the experience of the repairing Samsung Lcd monitors. Manual was made by m ... Samsung SyncMaster 940N Flat panel Monitor
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.7673 seconds