Having problems with your Proview PL913S 19" Flat Panel LCD Monitor ?

Proview monitor blacking out

\015 Hi, i have a proview monitor && for some reason after i have been on it for about an hour the screen blacks out. the power button is still on (the monitor) so i turned it off than back on but after two\302\240seconds\302\240it blacked out again. i made sure everything was plugged in and my\302\240computer\302\240wasn't over heating, but i still blacks out every hour. what do i do ?\015

Answers :

I would suggest getting a new monitor you might have made it overheat or your display driver failed.
I have this issue, only in Windows XP. My Windows 7 laptop, I can connect the 900p and it works fine! I can insert the Windows 7 install disk and the monitor works fine (had it on the install screen for about 40 minutes with no issues). I use it on the dell tower with XP Pro, screen goes dark after a couple of seconds. I use my XP setup disk, same thing.
Repair Help & Product Troubleshooting for Proview PL913S 19" Flat Panel LCD Monitor

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Proview monitor blacking out


I would suggest getting a new monitor you might have made it overheat or your display driver failed. ... Proview PL913S 19" Flat Panel LCD Monitor

LCD display Proview


The power inverter is the problem and the only way to fix it is to replace the board. It was a poor design and my Proview 19" experienced the same screen issues as those previously stated. You'll pay $25 for shipping and up to $65 in repair costs. ... Proview PL926WBi 19" LCD Monitor

My proview 558 monitor has a 1/2 inch black line at the bottom


Ms_biguns, You need to test one or the other, The tower should output and drive a substitute known good monitor, or a known good pc should be able to display the WIN-desktop screen on your Proview 558. Could it also be that the software in pc not set ... Proview Computer Monitors

Proview monitor won't keep the screen on


Bzinbby1, Hi, I think I know what's wrong. In fact I already know what's wrong! But I want you to do one test to let me know how bad it really is! Here is the test. I want you to reconnect your Proview to an already fully booted "KNOWN GOOD" pc wit ... Proview PL913B 19" Flat Panel LCD Monitor

Proview 900 series black flat panel monitor


Its sound you have bad inverter chip. The I.C. "BIT3193G" is the main controller in the inverter circuit. This chips is a surface mount chip and you must be careful remove it or you can damage the board. Also have you check for any burn out transisto ... Computer Monitors

LCD display Proview


You need to contact Proview. It is a problem with the monitor. I had the same problem and I was lucky. The warranity was going to run out in 15 days. They sent me a return number "I had to pay shipping and insurance" and they sent me a replacement ... Proview PL926WBi 19" LCD Monitor

Monitor turns off after 4-5 seconds


Hi every one, i hope this helps and am proud to say/or not that i am now using my philips php-19x (aka proview 900w/Mag LT916s Model 900p/ Xerox) and yes turn on the monitor 2 seconds screen goes black and the ... Computer Monitors

White screen When ever I turn on my pc my screen stays white. I turn off pc turn on again still no monitor only white screen. Does this 5 or 6 times before it comes on the right way


I had problem with a Proview 19? monitor:\015\012Product number: #PL926Wbi\015\012Model Number: 900W\015\012The monitor was manufactured in January of 2006.\015\012\015\012After I had owned and been using the monitor for 1 year and two weeks, it star ... Proview PL926WBi 19" LCD Monitor

Monitor goes blank less than a second after turning on.


Sounds like either there is a bad connection from the computer to the monitor, or the monitor has a faulty power regulator, causing the monitor to overheat prematurely, and shut off. ... Proview PL926WBi 19" LCD Monitor

No Signal when desktop wants to load


This is exactly what is happening to my monitor but happens a bit faster. Once the drive starts then the monitor turns on and turns straight back off again. The monitor works on other people's computers (including the tech guy at the shop I bought i ... ViewSonic VA1916w LCD Monitor

Proview Monitor PL926 Wbi The power indicator


Repair estimate will be according to problem. ... Proview PL926WBi 19" LCD Monitor

Proview PRO576 error message "mode not supported" and will show nothing else


Okay, we got a fix by having another monitor hooked up to our computer and going in to display and changing the display settings to a lower setting. The screen resolution - turn it to lower - I guess somehow - the setting was too high for our monito ... Proview PRO576 15 in. Flat Panel LCD Monitor

Dead Proview 700p monitor


My monitor samston 17`` have a problem with screen ten minute after on it`s become on / off screen ( it`s black, it`s white ) when it`s happen the wording can read, when it`s on. ... Computer Monitors

Proview 900 series black flat panel monitor


Same problem, and solution 1 given here fixed my Proview 900W. A few of the 470uF caps on the power board were oozing dielectric probably due to overheating. Hopefully the replacements will hang in there for a couple more years... ... Proview PL926WBi 19" LCD Monitor

Proview Monitor Blank display after 3 seconds issue


First place to look will be the power supply section, look for bad caps (bulging tops or bottom seals), the post back what you see so we can guide you further for direction such as voltage checking, see example of failed monitors due to bead caps: ... Xerox XG-91D 19" LCD Monitor

Proview pl716s monitor will not come on


I just had this problem with my screen (proview pl716s) if you open the case and take out the power board, there are 6 470 uf capasitors bundled together and 1 220uf capasitor replace all 7 and that should fix your problem , that is what i did and i ... Proview PL713S 17" Flat Panel LCD Monitor

Only brief display on my Proview PL926Wbi monitor


I have the same problem i have to keep turnoff than back on how can i fix it and where ... Proview PL926WBi 19" LCD Monitor

Power Surge damage. Suggestions on which part to replace.


Power Surge damage. Suggestions on which part to replace?\012 This trouble maybe power supply or inverter boards is defective.\012 first you can test the voltage of the multr,and then check which part is defective.From Wisiny.com can find those p ... Computer Monitors

Monitor turns on then off. - Proview PL926WBi 19" LCD Monitor


I bought Same Monitor Dec. '06 and Jus last week It faded to black and\015\012then now doesn't power on. my protection plan sent me a new one that\015\012powered on for like 20 secs. So now I have another one coming. I also\015\012knows its not m ... Proview PL926WBi 19" LCD Monitor

I have Monitor Proview PL916S 900P It turns on


This seems to be a Windows XP issues as I can use this monitor on my Windows 7 laptop without any issues. I hook it up to a Windows XP machine and it does this.... ... Proview PL916S2 Monitor

LCD display Proview


I would look on the power supply board and check for any capacitors that are bulged or popped. They look like little barrels with a cross or 3 line star on the top. This is the vent and it should split before the capacitor pops like a firecracker or ... Proview PL913S 19" Flat Panel LCD Monitor

Proview PL926Wbi O.K. I have a proview monitor that went black and iI have been told nits probably the capacitors on the inverter board. I've also been told that the capacitors bulge when they are bad. There seems to be no visible bulging or bad anything on any board,but on the brown side of the smaller board its a little dark brown under the Q5 & Q6 whatever they are. As far as the caps there is no visible bulging.Are there specific caps that go bad. What are ther numbers.


On modern capacitors 2005 or up the capacitors can go bad and not even bulge at the top. I replaced a few in my moms flap panel monitor and found out that there were more that were bad and they didn't show any signs of damage but put your finger on o ... Proview PL926WBi 19" LCD Monitor

I have a Proview 900w PL926WBi monitor FUZZY SCREEN!!


... Proview PL926WBi 19" LCD Monitor

Proview 926 wbi monitor


This trouble maybe power supply or inverter boards is defective.\012 first you can test the voltage of the multr,and then check which part is defective.From Wisiny.com can find those parts\012 if you have any question,please let us know email ... Proview PL926WBi 19" LCD Monitor

Monitor takes a long time to come on.


Blown capacitors on the power board replacmetn is recommended ... Computer Monitors
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3478 seconds