Having problems with your LG Flatron L1515S 15" LCD Monitor ?

Screen goes blank and message comes up saying "input signal out of range"

Answers :

When does the screen go blank? Also what do you have plugged into it this most likely just because your input signal may be set at to high a resolution or frequency. Once I have more information I can assist you further.
Repair Help & Product Troubleshooting for LG Flatron L1515S 15" LCD Monitor

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Screen goes blank and message comes up saying "input signal out of range"

When does the screen go blank? Also what do you have plugged into it this most likely just because your input signal may be set at to high a resolution or frequency. Once I have more information I can assist you further.Thanks,Lee ... LG Flatron L1515S 15" LCD Monitor

Input Signal Out of Range

I have been having the same problem with my hpvs17 monitor when i start to use my web browser on linux distros. Now, for the next few days i am going to try my system on a regular crt monitor. if the monitor does not crash, than i will have to say th ... HP Vs17 17" LCD Flat Panel Monitor

Monitor won't stay on. Error message comes up that says "no input signal", then monitor goes out.

Problem with the monitor, monitor cable, or video output. For monitor, if you have more than one input, make sure it's set to the correct one. Try a different cable. Try a different monitor. Check your video card settings--if you see the BIOS boo ... HP PC Desktops

"No signal detected" when LCD connected with DVI-D Cable

Thank you for providing your configuration details.\015\012You have failed to specify wheather or not your LCD Display is under Warrenty.\015\012\015\012Perhaps these simple trouble shooting procedures will get the job done.\0 ... BenQ FP71E 17" LCD Monitor

NO SIGNAL What do I do?

These messages are normal when the computer truly goes into suspend mode or loses the video signal (such as when the computer is suddenly turned off).If the monitor displays any of these messages when the computer should be displaying vid ... HP PAVILION A6230N DESKTOP PC

Fujitsu c series labtop screen goes blank, the hooked up to a monitor, starts to work then says out of frequence and goes blank

The video resolution and/or frequency that's set in windows is not supported by the monitor you have plugged in. Restart the PC in VGA mode (hit F8 after the BIOS messages but before any Windows messages) and change the video settings to something ba ... Fujitsu LifeBook C6555 Notebook

Boot up computer. Nothing comes up on screen. Get a message:"information. No input signal." Everything is plugged in correctly.

\015\012check the cable on the monitor screen\015\012if after removing the data cable from the computer and it has no vertical color screen then\015\012try other dat ... PC Desktops

Dell 2407WFP Monitor losing signal and having colored line artifacts

... Dell UltraSharp 2407WFP 24" LCD Monitor

Trubleshoot Motherboard what is mother board prob and how can find n fix them....

More than 70% of all computer problems are related to cabling and connections. Ensure all cables are connected and connected firmly. IDE and floppy ribbon cables and power cables can often go loose. Ensure microprocessor, memory modules, and adapters ... PC Desktops

Signal out of range

1: Signal out of range meas the monitor can't handle the input refresh rate. lcd and Tft monitors usually supports 60 and 75Hz refresh rates.2: The Resolution you are using to view the desktop is too high, this number is depending on the size o ... Kogi L7CH Monitor

My acer laptop won't reboot to factory mode

Back up all of your data(music,documents,videos)before you do this..if you can boot up then use ubuntu,slax or other types of bootable cds\015\012\015\012to set it back to the factory setting you are going to have to get a xp installatio ... PC Laptops

My samsung 940N acts like a florescent tube, tries to start and doesn't

Use the self test feature.. follow the steps..\015\012\015\0121. Turn off both your computer and the monitor.\015\0122. Unplug the video cable from the back of the computer.\015\0123. Turn on the monitor.\015\012If the m ... Samsung SyncMaster 940N 19 inch LCD Monitor

The monitor leaves a message no input signal, then " going to sle

That signal means the monitor is not getting any signal from the computer. It probably means your video card or connection is bad. You can buy a pretty cheap ($35-$100) video card from a local store (Best Buy, Circuit City, Radio Shack) or online. ... Compaq fs740 17" CRT Monitor

Going to Sleep

Due to the power surge, it is highly possible that the monitor was given a boot by your computer on it's way out.\015\012\015\012This will short out a very small transistor inside the monitor on the video board and in turn, then monitor c ... HP Pavilion F1903 19" Flat Panel LCD Monitor

Hello, My color isn't right on my computer. The box that pops up says "RGB no input signal". How can I fix this problem? Thanks Debbie


Monitor says no input signal

Do the icons look ok when you can see them? It sounds like your resolution may be way too high for the monitor. It loses sync and blanks the screen rather than show a lot of mess.\015\012\015\012Boot your windows in safe mode (tap F8 befo ... PC Desktops

Dell 2001FP can't change input modes

... Dell UltraSharp 2001FP 20.1" LCD Monitor

Computer monitor comes on for 1 seconds, flashes "analog power save mode" and then goes black.

Most monitors will say "Power save mode" when they can tell through residual voltage that the signal lead is plugged into a machine, but there's no picture being transmitted. The four states of a monitor are:* Off entirely.* Switch ... PC Desktops

I have a hp desktop model a1268c computer. after an update my computer srcreen says ''input not supported'' and the screen is blank. When the computer boots the F1 button ''setup'' works but the F10 button does not. After the computer goes past the XP screen then goes black with the message from above. The only screen I can see is setup.

> You needs to configure your scree resolutions and other parameters.> May be frequency rate doesn't supported by your old Monitor.> Just attach your desktop with different monitor and change parameter to lowest frequency range. ... Computer Monitors

Screen shows message "no input signal" and monitor goes to sleep.

Monitor show "no input singnal" error masage when not gating any type of video singnal ,\015\012so if u realy check your monitor wires for correctty plugged in . \015\012then:- Two possibilities:\015\012either the ... HP vp17 Monitor

My notino uL100 notebook laptop isnt working! PLEASE HELP!!!

My notino ul-100 notebook laptop is not working everytime i try to turn it on a message comes up on a black screen saying that windows root system32 hal.dll can not start bcause it is minssing or it is corrupt can you please help and tell me what i n ... PC Laptops

Monitor screen begins as computer is booting up and then screen goes black. Message says there is no signal.

If the power light dims or changes color after the no signal message comes up, that means the monitor went to sleep.While the monitor is plugged in and on and the computer is also on, Try unplugging the VGA cable from the monitor. wait 30 secon ... ViewSonic VG2230WM LCD Monitor

Input signal out of range

You could try going into safe mode and make sure the correct drivers are installed and if they are then you can then set the correct resolution. ... Dell OptiPlex GX260 PC Desktop

When using computer for about 10 min, monitor goes blank with an error message of"No Input Signal" then computer rebuts several times. Any idea's?

Its possible that your computer maybe having a driver conflicting with your monitor. My suggestion would be reinstall the software that came with your monitor. If you don't have that go to the companies website that produced the monitor and download ... PC Desktops

VX900, Backlight Works, But no picture.

It is impossible to see defective components visualy, unless there was a serious burn-up or something like that. \015\012\015\012Without at least a DVM you cannot even verify if the power supply is functioning properly!!! \015\012 ... ViewSonic VX900 19" LCD Monitor
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 1.0768 seconds