Having problems with your HP W2007 LCD Monitor ?

Replaced motherboard and power supply. Monitor says No VGA Signal and No DVI Signal, then goes to sleep. Will not wake. Unable to load OS because I cannot view the monitor.

Answers :


Sounds like you suffered a power spike and fried some
components. So if you;re trying to use the same CPU and RAM they
may well have been damaged as well....

Unclear from your request whether you are getting a POST beep from the computer...

1) If you are NOT: could be that the CPU or RAM is faulty. If you have
more than one stick of RAM pull them out one at a time and try to boot
with just one stick in there...You can test the monitor on a friend's system.

2) If you ARE: Unplug the computer and wipe the BIOS by moving the jumper to the other position for 30 seconds then put it back plug back
in and try rebooting...

Good Luck!
Power up your computer. As soon as you can open the DVD/CD drawer and put in your OS CD. shut down the computer then reboot. Let me know how you make out. Thanks Dana
Repair Help & Product Troubleshooting for HP W2007 LCD Monitor

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Blank screen after boot up

This issue may occur if one of the following conditions is true: \015\012Cause 1\015\012\015\012 loadTOCNode(3, 'cause');\015\012 \015\012This issue may occur if you have a CD, a DVD or a floppy disk in your CD, DVD, or floppy drive ... Dell Dimension 3000 PC Desktop

We have Dell OptiplexGX745 smallform factor desktop computers that we need to run two monitors.

If your Dell Optiplex GX745 came with the ATI Radeon X1300 graphics card, that has One - DVI graphics port, and One - VGA graphics port, it's no problem.This link shows an ATI Radeon X1300, and the two above mentioned graphics ports, ... Intel computers9: P3 Computer Computer (Reconditioned) (CSINTELP3) PC Desktop

External display not displaying!

When you are able to view a video clip on the external monitor, We can rule out the issue with the software. Probably you need to check the connections and also the external monitor settings in the display. The reload might have changed the old setup ... Dell Latitude D820 Notebook

Blank Laptop Screen

... Toshiba Satellite M45-S265 Notebook

Blank Laptop Screen

Unplug everything from your laptop unplug the power from the laptop close it and turn it over remover the battery open and hold the on button(battery is still removed) for a 10 count, replace the battery\015\012turn on you can plug the power co ... Gateway MX6956 Notebook

Blank Laptop Screen

The same thing began to occur on my (old as the hills) Dell Inspiron 2650 about 2 months ago. I have tried updating the BIOS to the newest Dell has for this laptop but it didn't help. I also tried to update the video drivers (no help), regressing t ... Toshiba Satellite 1410-S173 Notebook

Replaced motherboard and power supply. Monitor says No VGA Signal and No DVI Signal, then goes to sleep. Will not wake. Unable to load OS because I cannot view the monitor.

Hi!Sounds like you suffered a power spike and fried somecomponents. So if you;re trying to use the same CPU and RAM theymay well have been damaged as well....Unclear from your request whether you are getting a POST ... HP W2007 LCD Monitor

I have a Gateway mx3422 notebook. I cannot get the display to clone when I hook it up to a projector. The notebook screen goes black and the display shows on the projection screen.

So, as soon as you hook up the projector, the LCD goes blank? 2 things control the output, the function key to enable the external video and the display settings in Windows. If Windows shows 2 displays (Control Panel, Display, Settings), then chang ... PC Desktops

Need to change resolution but cannot get onto desktop to do so as the monitor just goes to sleep

Plug it into your laptop and change the settings to the monitor to 800 by 600 pixels, then change the refresh rate to 60 hz or you could change it to 1280 by 1024 pixels and 60hz but it should work with 800 by 600 too, then plug it back into your des ... HP L1706 17" LCD Monitor

How to add second monitor to asus cg5270? - ASUS Eee PC 1000H Laptop

The Asus Essentio CG5270 is a desktop computer, so I see it was placed in the wrong category. No prob!Certain selected models of the Essentio CG5270 come with a graphics card. If you have this graphics card, you can use two monitors at th ... ASUS Eee PC 1000H Laptop

Monitor goes into sleep mode after a few seconds

This is normaly cause by incorrect power management settings.\015\012\015\012check power management setting in both windows and your computers bios\015\012\015\012you will not need to worry about the power management settings ... HP Pavilion a620n (PC028A) PC Desktop

I have a dell demension 4300 that recently started having issues, slow cutain effect, freeze ups. harddrive clicking away. Then one day I had the blue screen that said an error was detected. Then it wouldn't reconize the harddrive but it would go into the bios screen and then not do anything else. So I took it in to have it diagnosed and they said the edie circuit on the board was fried. They offered me a card option for the back but I opted to replace the motherboard with one that was listed as

CaSmogTech,There is a No Signal on the monitor because the monitor is not receiving a Video Signal.Your computer is not producing a video signal.In essence, your computer isn't working, because there is no Operating System on ... Dell Dimension 4300 PC Desktop

Monitor not supported

Well the monitor not being support is not the issue. the issue is the video card cannot produce a signal that is supported for the monitor. Its doing this to let you know also to lower your resolution because the monitor will pop if the resolutions i ... HP dc7700 PC Desktop

Input not supported

Do you get anything on the screen when you first turn on your computer?If you do the windows resolution somehow got set to high for the screen to handle. To fix this press the F8 key a couple times after the BIOS splash screen goes away ( ... View and View Technologies VNV AquaView 17XP 17 in. Flat Panel LCD Monitor

15inches monitor troubleshooting

Hi Rachel, \015\012The old monitor was set to a resoloution that is higher then you current monitor can handle. This is normally the case when changing from a CRT to an LCD\015\012\015\012Try this:\015\012Unplug the video cabl ... HP Pavilion F1703 17" LCD Monitor

Problem with my LG monitor L194WT

You will have to increase the referesh rate first and then go into the game and reset the resolution. The resolution bit is secondary. If increasing the refresh rate works, then you dont have to change the resolution :) ... Computer Monitors

Dell Inspiron 6000 monitor display problem

Well it is most likely a issue with the Video driver as you are able to boot to the safe mode.I would suggest going back to the safe mode and deleting the present driver for the video from the device manager.before you restart the system just downloa ... Dell INSPIRON 6000 CENTRINO 1.7GHZ,512mb,40GB,DVDRW,XP (086216118098) PC Notebook

Dimension 4500S I have Dell Dimension 4500S it was working very good but sudden starts booting-up but after the windows XP logo finish loading up, the display goes blank, it has power all the lights in back of the computer are ok but nothing come to the display. I disconnect everything like modems, cd drivers and so on I also change the power supply but nothing happens. Can somebody help????

Hi lidio7, I would like you to click the link below & scroll down till you see Diagnostic Codes. Please follow the instructions listed.\015\012\015\012 ... PC Desktops

Dell screen (1901FP) won't come out of power saver mode

Hold down the Fn and F8 keys, and it worked fine for me.\015\012 \015\012or\015\012 \015\012if your problem is you cannot wake from power saving mode (after your PC goes to sleep, then its probably just the driver for your video card). VISTA has some ... Dell 1901FPt 19" TFT LCD Flat Panel Monitor

Screen goes blank(not Black, but dark) after windows boots

Perhaps it is trying to power an external monitor. Try this: Once your computer boots up, hold down the "fn" key (usually bottom row of keyboard) and then hit the key that shows what looks to be a monitor on it. Usually on the Toshibas, its the F5 ke ... Toshiba Qosmio G15 Notebook

Hp ze2000 shuts down

Without more information I cannot be sure, but I would say that it could possibly be set to use an external monitor. There is a FN key command to switch between your LCD Screen and an external screen. Try that. If you have an external monitor that yo ... HP Pavilion ze2000 Notebook

Monitor not working. dell prompts load, windows loads and then the screen goes black. i can hear the desktop being setup but cannot see anything

Check the data cable on the back of the monitor and the CPU.Also check the BIOS settings.\015\012\015\012Regards. ... Dell Inspiron 6400 Notebook

Periodically black screen while monitor light green

Hello,The problem is not the computer or software it is the monitor. The power supply in the monitor is going out. We repair these units all the time for the same problems that you have. We have repair guides on our web site showing how t ... Dell E173FP 17" LCD Flat Panel Monitor

Desktop screen display goes blue

Can u boot into the system?if not it can be solved if yes then there is a problem with ur monitor \015\012if u cannot boot intoo the system load default or system restor tht u do ,......savio k frm mumbai ... HP D2835 17 in. CRT Monitor

I have just loaded xp onto my equium 3200m but now the monitor goes onto standby after bootup. How can i fix this?

When loging on windows press F8 button then choose Safe mode.\015\012If your monitor work on safe mode \015\012so all you have to do is to change your screen refresh rate & settings\015\012Right click on your desktop > proper ... Toshiba Equium 3200M (PV1058U-4CNS2) PC Desktop
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.8053 seconds