Having problems with your Hansol Computer Monitors ?

Monitor displaying out of range message - Hansol Computer Monitors


Answers :

Hello and Welcome to FixYa!

This usually happens when you select a resolution or a refresh rate that is beyond the monitor range. For example if your monitor supports a max. resolution of 1024x768 then if you give it a signal of 1600x1200 it will display out of range.

Solution of this problem is to reduce the resolution or refresh rate frequency.

\015\012Changing screen resolution in Windows XP:\015\012First right-click on the desktop and then left click on Properties from the menu that appears.\015\012

\015\012The display properties dialogue box will appear as shown in fig 1.1 below, click on the settings tab at the top right of the box.\015\012

\015\012 xp-screen-resolution-1.gif\015\012

\015\012The areas worth noting are:\015\012

\015\012Screen Resolution\015\012
\015\012This slide bar is what you use to change the resolution, the options\015\012you have will depend on your graphics card and monitor, but the\015\012standard options are 800x600, 1024x768 and 1152x864.\015\012

\015\012Normally the default (in XP) is set to 800x600 which means the display will be 800 pixels wide and 600 pixels high.\015\012

\015\012\015\012How to Change the Screen Refresh Rate of Your Monitor\015\012\015\012 loadTOCNode(2, 'summary');\015\012 \015\012
    \015\012
  1. Click Start, click Control Panel, click Appearance and Themes, and then click Display.

    Alternatively, right-click the desktop, and then click\015\012\011\011\011\011Properties.
  2. \015\012
  3. Click the Settings tab, and then click Advanced.
  4. \015\012
  5. Click the Monitor tab, and then click the screen refresh rate that you want to use.\015\012\011\011\011\011
NOTE: \015\012\011\011 \015\012
    \015\012
  • The default refresh rate setting is 60 Hertz (HZ); however,\015\012\011\011\011\011your monitor may support a higher setting. Check your manufacturer's\015\012\011\011\011\011documentation for information about the settings that your monitor\015\012\011\011\011\011supports.
  • \015\012
  • If you use a higher refresh rate, you can reduce the rate\015\012\011\011\011\011that your screen flickers; however, if you specify a refresh rate that is too\015\012\011\011\011\011high for your monitor, your screen may become unusable and your hardware may be\015\012\011\011\011\011damaged.
  • \015\012
  • Changes to the refresh rate affect all users that log on to\015\012\011\011\011\011the computer.
Source:
http://www.helpwithpcs.com/tipsandtricks/changing-screen-resolution-win-xp.htm
http://support.microsoft.com/kb/311403

Kindly rate me if i was helpful.
Regards,
Waqar

I CHANGED THE SCREEN RESOLUTION NOW%2CTHE SCREEN IS SHOWING OUT OF RANGE .PLEASE HELP ME%3F
Repair Help & Product Troubleshooting for Hansol Computer Monitors

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Monitor displaying out of range message - Hansol Computer Monitors


Hello and Welcome to FixYa!This usually happens when you select a resolution or a refresh rate that is beyond the monitor range. For example if your monitor supports a max. resolution of 1024x768 then if you give it a signal of 1600x1200 ... Hansol Computer Monitors

Monitor out of range when a game is booted up


The maximum resolution for the MV540 is 1024X768 @60Hz refresh. The other monitor isn't giving you an error message because not all monitors have that feature, but both the monitors are unable to display whatever data the computer is sending. If the ... Compaq MV 540 15" CRT Monitor

I changed Desktop resolution setting to higher, Monitor went black with "Out of Range" message


Please try this:\015\012To resolve this behavior, either change the refresh rate, or change the video adapter settings.To change the refresh rate:1. Restart the computer, and while it is restarting, press F8 until the St ... Planar PL1910M (Black) 19 in. Flat Panel LCD Monitor

Outof Range error message & black screen


To resolve this behavior, either change the refresh rate which is what is chnaged or the resolution or change the video adapter settings.\015\012 \015\012\015\012To change the refresh rate:\015\012\015\012 ... HP L1940 19" LCD Monitor

Screen shows different colour grids when starting then goes black with message in right corner "out of range"


Hello ssi1,This happens when your screen resolution is set to something higher\015\012than what your monitor can display. For example, if your monitor\015\012supports resolutions of up to 1024x768 and your video card allows you\015\012to ... PC Desktops

DELL E153FPf doesn't show the image


OSD Warning Messages\015\012A warning message may appear on the screen indicating \015\012 that the monitor is out of sync range.\015\012\015\012 \015\012\015\012 \015\012 \015\012 \015\012 Cannot \015\012 Display This Video ... Dell E153FPf 15" TFT LCD Flat Panel Monitor

Attention out of range is displayed on ibm 2 74 monitor


To resolve this behavior, either change the refresh rate, or change the video adapter settings.\015\012To change the refresh rate:\015\012\015\012Restart\015\012the computer, and while it is restarting, press F8 ... IBM E74 17" CRT Monitor

My ViewSonic computer monitor keeps displaying a Vga Not Support Message upon booting then the message Out Of Range comes up on a completely dark screen. Need Help


It sounds like the computer is trying to use a resolution that the monitor cannot handle. Boot into safe mode by pressing the f8 key during boot up and select safe mode. Once booted, right click on the desktop and select properties. In settings lower ... ViewSonic VA721 17" LCD Monitor

Out of Range message displays when PC boots


To resolve this behavior, either change the refresh rate, or change the video adapter settings.\015\012To change the refresh rate:\015\012\015\012Restart\015\012the computer, and while it is restarting, press F8 ... Westinghouse 22" Widescreen LCD Flat Panel Monitor

Monitor Problem We Have the Princeton VL 173 Monitor and when we hooked it up to the computer the Monitor Turns on and trys to Load Windows XP and then The Message Appears that It is OUT OF Range and these Numbers Appears H 53.8 KHZ and V 85.2HZ and then Monitor goes into Sleep Mode.


That is because your computer is trying to display a picture at a higher resolution than the monitor can handle\015\012\015\012EG. if your monitor was only capable of lets say 800 x 600 and you deci ... Princeton Digital VL1916 19" LCD Monitor

"No signal detected" when LCD connected with DVI-D Cable


Thank you for providing your configuration details.\015\012You have failed to specify wheather or not your LCD Display is under Warrenty.\015\012\015\012Perhaps these simple trouble shooting procedures will get the job done.\0 ... BenQ FP71E 17" LCD Monitor

My monitor is linked to an Apple minimac. The monitor says out of range and gives a V: frequency 9 8kHZ anf H. frequency 1 19 HZ what does this mean and how do I reset it?


The message that appeared in your monitor "out of range" and V: frequency 9 8kHZ anf H. frequency 1 19 HZ has something to do with the screen resolution. Meaning that the resolution set on the computer did not meet the required resolution of the moni ... Computer Monitors

"Out of Range" Message


This happens when your screen resolution is set to something higher\015\012than what your monitor can display. For example, if your monitor\015\012supports resolutions of up to 1024x768 and your video card allows you\015\012to crank it up to 1600x120 ... Compaq Presario V400 14" CRT Monitor

Screen says "OUT OF RANGE H:27.8K V: 62.0 - Hyundai ImageQuest QV770 17 in.CRT Conventional Monitor


That's the monitor telling you it's getting a signal it can't handle. The H and V values are the horizontal and vertical frequencies that control the display. They change depending on your computer's video card settings. The monitor can be damaged if ... Hyundai ImageQuest QV770 17 in.CRT Conventional Monitor

Will not display output from Computer


Probably the video resolution or the monitor Refresh Rate (eg: 50/60/75 Hertz) is set too high in the operating system, which over-drives the monitor electronics and it is unable to display anything.If you restart the computer manually (h ... Westinghouse LCM-19v1 Monitor

Monitor displays Msg. frequency out of range, screen is black


Start your computer and press the F8 when the manufacturer's logo screen is showing. This will bring you to the Windows startup menu. Pick "start in VGA mode" and windows will start up with video settings you monitor can handle. Then you can change y ... Compaq Computer Monitors

StarLogic- Out of range


The computer needs its screen resolution reducing or changing in aspect ratio to suit the StarLogic monitor. Use a previously-working monitor and reduce the resolution on the computer to 1024 x 768 pixels or less (right-click an unused part of the d ... Star Logic 17" LCD Monitor

Westinghouse monitor displays big red OUT OF RANGE message - and computer is unresponsive- have to restart -new HP computer- 2 yr old monitor came home from work the last 2 days with this message displayed- computer will not turn off or restart - have to turn off at surge-


Your didplay setting is not supported by the monitor or your drivers for your vga need to be updated ... Westinghouse L2046NV Monitor

''Out of range'' message on an older SVA monitor


This usually means the display resolution settings on your PC are set too high for the monitor to display the signal. Try lowering the resolution on your PC. ... SVA-USA VR 17S 17" Flat Panel LCD Monitor

Phillips Brilliance 200W6 Monitor : Got power but black screen


... Computer Monitors

NO SIGNAL What do I do?


These messages are normal when the computer truly goes into suspend mode or loses the video signal (such as when the computer is suddenly turned off).If the monitor displays any of these messages when the computer should be displaying vid ... HP PAVILION A6230N DESKTOP PC

Over range message on monitor


Switch on the computer then press F8 F8 contineusly then highlight on safe mode press enter then display will see if you want to work on high resolution then attatch external display card and best will be AGP card then you can watch movie much clear ... Proview PL926WBi 19" LCD Monitor

Gateway FPD1530 loses image shortly after powering up.


Try booting into safe mode. press F8 while the computer is booting. see if everything stays normal. It should tell you that it booted into safe mode. Once there, change the resolution or the frequency of the display(also known as the refresh rate) by ... Computer Monitors

Input Signal Out Of Range


Some monitors have low resolution, that if it doesn't support that resolution then you'll expect an "input signal out of range" message on screen. try to boot on "safe mode" if it works then you have to lower your screen resolution at "display proper ... HP Pavilion F1523 15" LCD Monitor

I get error message: Out of Range, on my 17 inch LCD KDS monitor


Get the monitor that you used previously, and on the Windows desktop, go to display properties, in settings> advanced, under the monitor tab, change the refresh rate to 60, which is common on these flat panels. ... KDS Computer Monitors
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.8314 seconds