Having problems with your Gateway VX930 19" CRT Monitor ?

Swivel base removal

\015 Can I remove the swivel base from a Gateway VX900 monitor? I would like to lower the monitor by a few inches so my duel monitors are at approximately the same height.\015

Answers :

In the back of the swivel there is a small release lever... push down (?) then with other hand hit the swivel base towards back, then lift unit up.
Repair Help & Product Troubleshooting for Gateway VX930 19" CRT Monitor

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you take the base of a envision H170L


I just had to go through this ordeal myself and basically this monitor was never designed to have the swivel of the base removed easily. I had to unclip the whole plastic front frame from the monitor (I used tiny flat screwdrivers), however before yo ... Envision H170L Monitor

Swivel base removal


In the back of the swivel there is a small release lever... push down (?) then with other hand hit the swivel base towards back, then lift unit up. ... Gateway VX930 19" CRT Monitor

Not sure how to take the swivel base off for wall mounting on a 42lb1dra


If you look at the back of your TV,\015\012locate four big screw/bolts. Its the biggest screws/bolts you'll ever\015\012find at the back. 2 each side that holds the unit to its swivel base.\015\012roughly 12" from the left edge and 12" also from the ... PC Desktops

Removal of Base from Monitor


It's little trickey....u need to try and use little force and twist it to left or right and just pull it out....\015\012dont use any tools it can damage it...\015\012push it little forward / backward ...left /right...twist pull ... HP Compaq S9500 (Silver, Carbon) (Carbon, Silver) 19" CRT Monitor

How to replace screen on Pavilion dv7-1040us. is diferent from other hps I have replaced, cannot figure out how to remove it.


Here it is! Have fun!\015\012\015\012Remove the four 4 mm P1 Phillips-head screws that secure the hinges to the display panel enclosure. \015\012Remove the two 4 mm P1 Phillips-head screws that secure the m ... HP Pavilion dv7-1240us Notebook

Acer 1717 monitor- removal of base


At the base you want to remove - in order to pack the monitor - if you se at the rear left and right there are a tiny opening about 3 cm long,put inside a screw driver and it will open very easly the plastic cover.Then inside there are four screws,tw ... Acer Al2416WD LCD Monitor

I have a LG Flatron L1718S-BN and need to get to power supply inside monitor. I need instructions to remove the base and swivel stand. So monitor can be repaired.


... LG Flatron L1718S LCD Monitor

I have a Sampo S 1522 and the on/off switch will not always switch off the monitor. I need to press it multiple times to get it to turn off the display. Can the switch be changed? How do I get to it. Thanks RonW


Cord unplug, on safe working table.You have to open the back cover remove some of its screw, swivel base. Maybe some retaining clips. Detached the circuit board for space. Then your at it. Replace the switch with exact replacement. Then c ... Sampo AlphaScan 712 Monitor

How does one remove the swivel base for packing


... ViewSonic A91F+ 19 in.CRT Conventional Monitor

Remove base of envision lcd monitor G19LWk


The base of the G19LWK can be removed but it takes a little work. You have to remove the black plastic case that sandwich the LCD screen. First remove all the screws on the backside of the monitor. Then, at the seam of the two casement halves, GEN ... Envision G19LWK Monitor

How do I open my HPw 1907 Monitor - HP w1907 LCD Monitor


Start by removing the base. There are 3 screws. First pull the base\015\012plate off. Then remove 2 screws. Next remove the little rubber insert\015\012in the center of the base bracket. You will need a long phillips to get\015\012to the 3rd screw. S ... HP w1907 LCD Monitor

The connection where you plug in the power on my compact presario R3000 laptop is broken. The female part that you plug into is loose and probably broken away from the solder on the mother board it self. I can hold the plug in and move it to charge the battery, but as soon as I let go it stops charging and the computer shuts down. how do I take it apart to resolder the connections?


Before you pull apart your laptop, check the male connector and power cord of the adapter, check it with a multimeter and or plug it into another Compaq. You could have a broken wire in the power cord, it could save you a lot of work.\015\012 ... PC Laptops

How do you remove the base from the hpvs17


Please look here..and vote me if its works.. its in German but good pictures maybe it will help you.http://images.google.nl/imgres?imgurl=http://mperlitsch.hintergrundbild.com/hp/HP1702_klein.jpg&imgrefurl=http://mperlitsch.hintergrundbild. ... HP Vs17 17" LCD Flat Panel Monitor

Gateway 610XL Disassembly


Take cover off top of base.- pry offremove two screws that hold speaker unit, it will tilt out, disconnect cables and remove speaker.two screws on back of base and then take off back cover.remove sheild cover.disconnect all cables. ... Gateway Media Center 610XL PC Desktop

Disassembly of gateway 610XL


Take cover off top of base.- pry offremove two screws that hold speaker unit, it will tilt out, disconnect cables and remove speaker.two screws on back of base and then take off back cover.remove sheild cover.disconnect all cables. ... Gateway Media Center 610XL (610XLMDIA) PC Desktop

Acer AL1917W goes black


I have recently opened my AL1917 (not wide) but it should work the same. First remove the stand. This is done by removing the plastic cover over the stand hinge (which appears to be part of the back cover, but is'nt.) Mine was done with simple tum ... Acer AL1917W LCD Monitor

How do you take apart an HP w1907 monitor? I have one that the picture only stays on for a split second at power up and then goes blank. I suspect a filter capacitor but can't take it apart to check.


Haha, been there. This ones a little tricky. Hope you have strong\015\012fingers. start by removing the base. There are 3 screws. First pull the\015\012base plate off. Then remove 2 screws. Next remove the little rubber\015\012insert in the center of ... HP f2105 21" LCD Monitor

Stop Error: c0000221


This issue may occur if any of the following conditions exist: \015\012\015\012\015\012\015\012•\015\012A damaged file exists in the folder in which Windows is installed, and this file is not overwritten during Setup. For example, if you receive ... Compaq Evo N1000C Notebook

Hp pavilion f1930 shows pic for 2 secs. then blank


Rather than guessing, or blaming the computer, I fix the F1903 backlight problem. Power the monitor and using a bright flashlight check the screen to ensure there's an image, or the menu when you press the menu button. Nearly every one of the F1703 a ... HP Pavilion F1903 19" Flat Panel LCD Monitor

VG930M-3 Taking base of this monitor...


After a chat with a Viewsonic tech and pulling out a lot of screws, this is what I discovered you have to do;\012Find a secure place to turn your VG930M upside down, like on an armchair.Undo the central screw on the base and r ... ViewSonic VP920b 19" LCD Monitor

Amilo Pro V2010 base removal


HiThe inverter is in the laptop screen, not the base. 1 remove the screw covers and then the screws surrounding the laptop screen2 gently prise the screen bezel away from the screen, best done when the laptop is opened out almost ... Fujitsu Siemens AMILO Pro V2010 Notebook

Blue screen problem


This Issue has 2 major reasons. There are several methods to fix the\015\012issue as Microsoft published on the knowledge base. I am adding the\015\012full info including the method that you can find on following link.\015\012Please post your questio ... IBM ThinkPad A31 Notebook

Removing laptop from docking station


If you have the ArmadaStation EM:The issue of removing the notebook is compounded by the fact that the ArmadaStation EM uses a motorized dock/undock mechanism to remove the notebook. When the expansion base has no power, it is unable to e ... PC Laptops

Optiquest Q9 After about 14 months, my 19" LCD Optiquest Q9 monitor suddenly got very dark ( the bottom 1/4 was still viewable, though dark) and then went blank. After it cools for a while I can power it back up with the same results. There is a faint click when it goes black. I have replaced it with another 19" LCD ( different MFG.) which is working fine, but hate to throw this one away if it is repairable. The screen itself seems fine with no pixels missing at the time it went dark. There are


I had this problem with my Q9 and I was glad to find the FixYa website with help. But I will offer more detailed info for novices to make sure you find the capacitors. First of all, it is not easy trying to find out how to open the monitor up! First, ... ViewSonic Optiquest Q9b 19" Flat Panel LCD Monitor

LCD Monitor How do I open the back cover


1st remove the base cover by by squeezing to release the clips and remove the 6 base mounting screws. 2nd remove the 5 screws in the back cover. 3rd push and pry at the parting line to release the clips. 4th remove the base mount by removing the two ... Acer AL1717 17" LCD Monitor
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3747 seconds