Having problems with your Encore Software Kawasaki Jet Ski Watercraft for Windows ?

Jet Ski Will not start when cold

\015 I have 2 1999 Kawasaki Jet Ski 1100 STX. Both of them have the same problem. They will continuously crank and not fire up. I think its a fuel problem because i did not put stabilizer in before the winter. I cleaned out the lines and pump thing on the rear of the engine, and took out the diapram and cleaned it. If i take the cover off the 3 carbs and spray some gas I can get it to start and run fine. It will start again no problem but as soon as the engine goes cold, it won't start and I have to take the carb cover off and put more gas in. That obviously isn't a permanant solution. Any suggestions?\015

Answers :

If the teeter/totter needles are gummy or covered with moisture corrosion it could be the reason the machine is so hard to start. When storing the jet ski's syphon all the gas out and burn it in your car or truck. Even if you stabilize it it wont be good fuel in the spring. Your plastic tank will not rust so remove the fuel. You may be able to clean them up by running a tank of Chevron Techron through them. Before riding we charge are batteries and start are jet ski's on the trailer/lift before dropping in the lake. This saves the battery. It takes more juice to start the boat in the water.
Repair Help & Product Troubleshooting for Encore Software Kawasaki Jet Ski Watercraft for Windows

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Jet Ski Will not start when cold


If the teeter/totter needles are gummy or covered with moisture corrosion it could be the reason the machine is so hard to start. When storing the jet ski's syphon all the gas out and burn it in your car or truck. Even if you stabilize it it wont be ... Encore Software Kawasaki Jet Ski Watercraft for Windows

Jet ski is sparking but will not start - Encore Software Kawasaki Jet Ski Watercraft for Windows


Air in fuel lines, vacuum line to pump cracked or leaking, corrosion in carb on teeter totter needle(float type needle). ... Encore Software Kawasaki Jet Ski Watercraft for Windows

P4 PC with Antec power supply won't start when cold


I haven't heard of a sensor that keeps it from starting when too cold. Usually in electronics, if it is a cold problem, there is a cold solder joint somewhere. When you apply heat, the joint solder expands enough to make contact and once electricity ... PC Desktops

Jet ski wont start, no lights no nothing,, battery is new and been tested twice


Check your ground wire, and also check to see if you have a fuse/fusible link that went out. ... Encore Software Kawasaki Jet Ski Watercraft for Windows

LG L1900E flickering after cold start


This is probably due to a bad solder joint somewhere. Bad solder joints can effect a unit in the reverse also. IE works at first and then dies after it gets warm. Think about how metal expands when it is heated. And contracts as it gets cold. If ther ... LG Computer Monitors

Keeps blinking out to a black screen


Hi,If the power light stays on and the unit works even if for just a moment, then chances are that you either have a cold solder, or a heat problem with some components or your CCF Lamp is starting to fail.All possibilities re ... Computer Monitors

Monitor cold start issue only as #2 monitor


The start up problem is common and will only get worse. Call Samsung as these monitors have a 3-year warranty. No receipt? They will accept your word regarding your purchase. I have\015\012two that failed exactly the same way. I called 1-800-SAM ... Samsung SyncMaster 931B 19" LCD Monitor

P4 PC with Antec power supply won't start when ''cold''.


The first thing you should do is replace the power supply with another and see if the problem continues. if it does call me and we will work it out \015\012\015\012Marc\015\012215-729-1745 ... PC Desktops

Black screen at start up?


IT SOUNDS THAT YOU HAVE A COLD SOLDER !! open the unit and check out the printed board and look around the transformer for a burnt or cold solder , re solder it and youre good to go , let me know , AJ ... Gateway FPD 1730 17" Flat Panel LCD Monitor

Hi, I have just installed a brand new printer into my computer and when I switched the printer on the computer restarted automatically with a blue screen error. This has happened before with memory sticks and MP3 players, but only started happening about 6-8 months ago before that it worked just fine. Can you help please? Thank Niki


There are 3 things to try, I'm pretty sure that more than one is the culprit. 1. IRQ settings(aka communications ports/usb) are very susceptible to malware/spyware/virus. What type and frequency of virus and spyware tools are on your PC? Update yo ... PC Desktops

The power light keeps flashing orange - PC Desktops


I had my Optiplex GX520 at work shut down abruptly every time I turned it on it in the morning. This would always happen within the first 30 minutes. I would then get the flashing amber light. After starting the PC again, it would stay on al ... PC Desktops

Noisy fan after a few minutes start up


Yeah. i had this problem too. the fan is noisy because it is garbage. it needs to be replaced if you want to get rid of the noice. you moving the laptop wen the noise first started is just coincidence. the heatsink is fine, but the fan itself is poor ... Acer Aspire 5100-5033 Notebook

92 honda You ll have to forgive me, i dont know a lot about this kind of stuff. I dont have a factory manual. All i have is information that i was able to get from my friend. It's ALLDATA 9.70. The diagram it shows, it doesnt show an orifice tube, just an exspansion valve that i did replace. I was told that it surved the purpose of the orivice tube. I did replace the stuff from auto part store components. The reciever dryer doesnt have a sight glass on it niether did the old one. The system work


35 PSI is not low enough on the low side, it should be 30 PSI, is the pressure cycling switch adjustable?? if so try turning the screw under the connector out half a turn to start and then recheck, and so on, or just replace it, if you can't the PSI ... Dell Inspiron 1501 Notebook

FLATRON L1717S - lines accross screen when cold


... Computer Monitors

IBM T30 - no screen - sortof booting


I own a t-30 myself with all the same problems i am reading about not reading ram beeping on startup no screen display but you could here hard drive running before these symptoms started the first symptom i ever noticed was if i picked the unit up wi ... IBM ThinkPad T30 2366 Notebook

Screen resolution is locked at lowest setting!


Hi!\015\012\015\012you cant change the resolution? did you check the video card driver in device manager? check if the driver is installed properly. if not, then download the latest video driver at support.dell.com > go to drivers and ... Dell Precision M60 Notebook

Sony Vaio Display problem


Hi,Since the Sony Vaio VGN-CR220E works except that the display is dark, then it\015\012would be safe to assume that it is only the LCD display part that is\015\012the issue. Often LCD display (of laptops) are working but only that you\0 ... Sony VGN-CR220E/L Notebook

I have a 1992 kawasaki stand up jet ski witch does


... Encore Software Kawasaki Jet Ski Watercraft for Windows

Soyo 17'' Monitor (DYLM017A)(VT17N71), identity of fuse.


Orange color of the ring means number 3. Part of marking also contains "3A" so I'm pretty much sure it is 3 Amps rated fuse. But before replacing it measure the resistance on the PCB where that fuse was blown, between common mask (usually metalized m ... Computer Monitors

Wont boot up to bios


I have had TWO recent model NEC laptops with the same symptom in the past 5 months. I was quite surprised, since NEC is a quality product. But the problem was the DVD/CD-Rom, which is made by Philips (mine were Philips SCB5265 models, but there are o ... NEC Versa SX Notebook

Emachine wont start


How many hours you working you computer? 1 or 2 or 3 hours?\015\012if you working 2 or 3 or 1 then automaticaly shutdown then, when you push the power button the cpu fan is working but in few minuts shutdown again,.... check you cfu pan maybe t ... eMachines T6211 PC Desktop

Hi I have a compaq fs7600 pc. For the past few weeks I have been experiencing sudden "black screen" and then my hard drive shutting down. Or it will go black screen and my hard drive will beep. It is usually one fairly long beep, then repeats about 3 or 4 seconds later. I only have 512mb of ram, which came with pc. I plan on buying a 2g of ram next week. Will that solve this problem? My pc is about six years old!! I know! Dinosaur!!


Hi.If the computer is suddenly shutting off, then I doubt that a RAM upgrade or replacement may fix the problem.A faulty RAM module will cause the computer freezing but staying on, or the computer turning on, but not starting ... Rosewill R900J 19" Flat Panel LCD Monitor

Screen went black


When you close the lid, there is a small pin that engages the case and flips a switch to tell the laptop the case has been closed. The monitor will ALWAYS turn off then, because otherwise, the heat build up would burn the screen! Do not try to defeat ... Dell Inspiron 710m Notebook

We have an Envision 9410e 19" LCD monitor which is about 4 years old. Recently it has started being very slow to start up, especially in the morning after the system is not in use all night. The screen stays black "too long," then it starts flashing, so that the user only sees the images for an instant, alternating with black. After a couple of minutes, the picture kicks in. Sometimes it will do this later during the day, after a break, but not always. / We tried switching the monitor with the o


Cmgusa, Reconnect 9410e to original PC. Please note if same symptom occurs again. This sounds like an intermittant or failed solder connection of some component on the inverter/smps power supply board. Have you tried the FLASHLIGHT test when the moni ... Envision 19" Widescreen Flat Panel LCD Monitor

WET LAPTOP I left my laptop near the window and went out partying. It rained that night and my laptop got wet. My laptop was in shut-down mode but was connected to the AC supply. When I reached home, I wiped it with a towel and tried to turn it on. The power light would come on but the system wouldn;t turn on. I left it to dry the entire night. Next morning I kept it under the sunlight for a couple of hours. Again tried turning on. This time it would turn on but keybord wouldn't work. So I left


Multicolored vertical bands means that the contacts on LCD ribbon cables are still shorting because of liquid or oxide building in consequence of liquid damage. Also keyboard is probably not working for same reason. ... Samsung R610-64G Laptop
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.4512 seconds