Having problems with your eMachines EL1210-11 PC Desktop ?

Unplugged power button from emachine t3624 forgot how to

\015 Unplugged power button from e machine t3624 forgot how to plug back in.three wires red white blue white black white there are 4pins on top 5 on bottom dont know witch one.\015

Answers :

If you can not see a "+" and "-" sigh on the connector as well as on the motherboard, then try it both ways. If you get it wrong the first time, it will not harm anything, just plug it in the other way if it does not work. Good luck!
Repair Help & Product Troubleshooting for eMachines EL1210-11 PC Desktop

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Unplugged power button from emachine t3624 forgot how to

If you can not see a "+" and "-" sigh on the connector as well as on the motherboard, then try it both ways. If you get it wrong the first time, it will not harm anything, just plug it in the other way if it does not work. Good luck! ... eMachines EL1210-11 PC Desktop

Emachine T3624 will not power up

Emachines are notorious for having faulty power supplies. If your lucky you just need to replace the power supply. I've seen a lot of them where the power supply also fried the motherboard.\015\012 \ ... E-Machines T2984 PC Desktop

Emachine flashing yellow lights, fans power up when P8 is unplugged

I would also suggest that the battery in the motherboard be replaced.That battery is startup power for the computer and if the battery is dead you will have the same symptems of startup power problems!!!The battery you will be looking at looks like a ... E-Machines eMachines Desktop PC

EMACHINES won't boot

RE:" When hold power button on the 2 fans spin freely, but when release it both stop"That means that there is an hardware fault.Try first unplugging power cord, and pluggign back power after one hour. This will drain power fro ... E-Machines eMachines Desktop PC

EMachine T3958 Won't start - Please help

The green LED indicates that the standby voltage is present which is what provides the power so the front button can tell the unit to turn on fully.\015\012At that point, there are 3 possibilities; the power supply has a fault and won't turn on ... E-Machines eMachines Desktop PC

I have a emachine W4885 desktop that won't bootup.

First unplug it and remove the case (usually two screws on the back) then plug it back in and start it while looking inside. Are any fans moving? are they clean and free of dirt? \015\012If no fans are moving, i would presume it to be a weak po ... E-Machines eMachines Desktop PC

Emachines W3052 Gets stuck on logo screen when starting up.

My computer does a similar thing, the issue with mine is the mother board which requires everything to be at a certain temperature. Let it run on the start screen for a couple minutes and hit the reset button. If it doesn't boot up you're going to ha ... E-Machines W3052 PC Desktop

PC won't boot after changed BIOS memory settings

With all that you've done, you might have worsened your PC mobo's condition. Now try to remove the processor and memory then PLUG it normally to the power outlet and see if the led in the mobo lights. After 3 minutes, unplug it and reseat the rams an ... Toshiba Satellite A135 Notebook

EMachine will not turn on.

Sounds like the power supply is faulty. Power supplies are very dangerous to try and repair, even for qualified technicians. I would also suggest not trying to plug it in or turn it on until the new power supply is in place. Faulty power supplies ... E-Machines eMachines Desktop PC

Wires from switch came unplugged (white and black) where do they

Power On switch (Button)? Restart switch? Speakers?Wires came loose from the motherboard?Should like you to see if you can trace the wires back to the front panel, (Where the Power On button is located Granted, this may be a little tough ... E-Machines eMachines Desktop PC

Replaced power supply on T2240 emachine now cant get onboard video" or any video,also tried PCI video card with no results. Need video to see if machine can boot

Unplug the computer for at least one minute. Press power button for 4 secondS while the power cord is unplug. Plug it back listen for beeps short and long beeps count them and refer to bios codes. If nothing happens remove everything from the mothe ... Intel PC Desktops

The yellow power led light blinks on front of the emachine w2646. The CPU Fan works. The power button will not turn the PC on or off, you just have to plug in the power cord to turn it on. The monitor just stays at a black screen. the Cpu Fan spins. i have replaced CPU, Ram, Power Supply. With no change to the system.

Did you flash the main board ??1.) remove battery2.) press and hold the power button for 10 - 30 seconds3.) replace battery.4.) when the system boots it will say press XX (e.g F2) to load defaults and continue ,, press t ... E-Machines eMachines Desktop PC

Emachine W2646--lights blinking on keyboard,pwr lamp on speaker on,power button on tower YELLOW,NO response! unplugged several hours,now dead,as if unplugged! This happened overnight while shut off completely,no one touched.

If you have a Yellow light on power supply, chances are you have blown the power supply.\015\012Even with a PC unplugged in a Bad Storm, I have seen many PC's and Laptops with Supplies shoot.\015\012If you ... E-Machines eMachines Desktop PC

I unplugged my emachine desktop when i went on vacation and now after repluggging it is dead to the world?

Hello there:This is fairly common on these e-machines Normally what happens is that the silver coin sized cmos battery will drain down and when this does by default it shuts it'self completly down untill you replace the battery ill nee ... PC Desktops

No post, only motherboard light on, green.

Unplug the computer from the AC. Push the power button down for 5 seconds. Unplug the power and IO to each device and remove memory chips. Plug the computer back into AC. See if you get POST(a beeping noise). It should beep once. If you get a series ... Dell Dimension 2400 PC Desktop

Emachine with XP home edition doesn't start

Hi hearalso, down to the basic's. Replace power cord. \015\012No help there than, remove the case's side panel to expose the motherboard. (Normally it is the left side panel while facing the front of the PC.)\015\012Look closely for a sma ... E-Machines eMachines Desktop PC

Emachine t3958 Hi, I turned off my t3958 by pushing the power button and now it want come back on. I ohm the switch, not sure what it should be but it 0 out. I pulled out the mother board and inspected it, nothing looks or smells burnt. With the mother board out I plugged the power supply in to a outlet and one fan started running but only for a second then stopped. I then waited a few minutes plugged it back in and it did the same thing and if I unplug and then plug right back in again it does

First check to see if a drive died. Unplug all the drive Floppy, hard and dvd or burns. I have come across many time that a drive will die and keep motherboard from booting. Being that you say you get a green light on the motherboard shows that the ... E-Machines eMachines Desktop PC

I have a EMachine T6534 which won't start. I shut

Most computer repair shops have a tester that they can hook up to your power supply. You can also purchase one for yourself, they usually run $25-50, it may be viable to purchase one if the shop will charge that much to test. ... PC Desktops

I changed the fsb from 166mhz to 200mhz on my computer

You will need to clear the coms 0n the motherboard to do this shut it down and unplug it then look for a 3post/pin on the motherboard that says clear coms and has a jumper on it>move the jumper over one post/pin unplug it from the 2pins on the rig ... E-Machines W3052 PC Desktop

Emachine desktop The computer worked fine one day and the next day when we went to turn it on it would not power up. The monitor comes on and on the monitor screen it said monitor working fine check hard drive. Well I can't check anything because the tower has no power. The light around the button doesn't come on and you can't hear any kind of fan starting. Called emachines and the only thing they could tell me was to change outlets, did that, turn power off (no power) leave unplugged for 3 minu

I understand that your cpu is not turning on and the repairer confirmed that it is the issue with the mother board. I suggest you to please check the smps fan spinning or not. If its spinning then then the issue could be with the mother board. If not ... E-Machines eMachines Desktop PC

E-Machines 2862 Dead On Power-Up

You might want to try to unplug it at the power cord and then plug it back in again, ... E-Machines T2682 (000002965) PC Desktop

Emachine t2882: not powering up just an amber light. replaced power supply, still just an amber light. power supply fan runs, but cpu fan does not. reseated all connections. plugged in drives one by one, when connecting hard drive and diskette no light at all just power supply fan running. i plug in dvd and cdrom get amber light. no beeps no other lights nothing.

Hello there:\015\012ok unplug everything from the board first and power up and see what happnes. if nothing still unplug the powersupply to the motherboard and press in the power button and hold it in for 1 min and than plug in the powersuppl ... PC Desktops

Itt urns on but it stays on the emachine bootup

We can only try for a power drain for this issue,\015\012\015\012all you have to do is unplug the power cable from the computer and battery too, then press and hold the power button for 40sec( without battery and power chord), then connec ... E-Machines M5414 Notebook

Cannot shut off & no display

The eMachines M5105 is notorious for failing to boot if left unplugged and powered off long enough for the battery to become mostly discharged. Plugging it in to AC power will cause the battery to start charging; and the hard disk drive to spin whil ... E-Machines M5105 Notebook

Cannot open my computer

1. First of all, you need to shut off\015\012your computer. To do this press the power button on the front of the\015\012computer after you have shut it down from Start> Shutdown on your\015\012start menu.2. Unplug the power cord from ... E-Machines eMachines Desktop PC
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.6754 seconds