Having problems with your E-Machines eMachines Desktop PC ?

Emachine t2742 I also have a wiring problem!

\015 I inheired a t2742 with the wires to the front panel not connected. I saw an diagram you made for somone . I just found this site today and signed up my expertise is 41yrs gen. contractor. now I'm a dis. veteran trying to learn something, I would appreciate any advice thanks\015

Answers :

Gtater,
It's ironic that you ask me this question today-- i am just now carrying in another eMachine computer to fix. Anyway, unfortunately I do not have one that is the same model as yours (T2742). However, I did some quick research and found that yours has the same exact motherboard as the T2898 which I made the diagram for!

The following eMachine models share the same motherboard (and thus the same front panel layout):
T2742 T2796 T2798 T2824 T2885 D2823 T2862 T2896 T2898 T2958

284ecac.png

For further reference, I would like to share this diagram for the eMachines T6544 in case someone else may need this model. This is the computer I just carried in... might as well share.
ccd6456.png
By the way, the power switch doesn't need to be oriented any particular way (positive and negative), which is why the switches are not labeled as + or -. Switches can be wired either way and they will work the same.

Hope this helps.
Repair Help & Product Troubleshooting for E-Machines eMachines Desktop PC

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Emachine t2742 I also have a wiring problem!


Gtater,It's ironic that you ask me this question today-- i am just now carrying in another eMachine computer to fix. Anyway, unfortunately I do not have one that is the same model as yours (T2742). However, I did some quick research and found t ... E-Machines eMachines Desktop PC

Emachines problem... PSU works but comp doesnt turn on


Hi,\015\012I don't want to tell you a color because it could be different than the actual. Look at the front of the computer and trace the wire that goes to the switch and follow it to the mother board. If you have a volt meter you could measure the ... E-Machines eMachines Desktop PC

Bad power supply, installed new one, get green light on mother board; but doesn't boot up. Bad start up button?


Yes, it is my belief that it is the Power On button. To test this, there is a simple solution. I however, would like to caution you at this point.You will have the power supply plugged in. There will be a small spark. I wouldn't advise how to t ... PC Desktops

EMachine no power


Ok for a start the power switch is not green and white that is the power led, you need to look for a red and black wire normally marked on the connector and motherboard as pwrsw or pswitch.\015\012if you believe it to be the switch unplug the c ... E-Machines eMachines Desktop PC

Emachine t1840 wiring diagram power switch wire to mother board ?


Because there are so many different case and motherboard combinations\015\012sometimes it can be difficult following the instructions for connecting\015\012the front panel, USB header and audio header.\015\012\015\012Below is a few generi ... PC Desktops

THE SCREEN SMEARS NAD SHUTS DOWN


Hi eakesj:A number of things here should be checked.First shut down and remove all cards, and power connections to all the drives such as cdroms, hard drives. The power supply should also be looked at and tested for correct voltage ... eMachines T6534 PC Desktop

I am trying to remove the outer case to an emachine t2742. Can you help me?


Hello mbrown1057\015\012\015\012HERE is eMachines listing of downloads, etc. for your T-2742 desktop PC. ... PC Desktops

Emachine t series keeps rebooting. Turn the computer on windows logo shows than the emachine logo shows than it shuts down and restarts. It does this over and over. Nothing else. Except when I push F2 or F12 than it goes to the bios. than it will stay in bios until i close it.


Possibly it has a corrupt windows, has lost the boot sector to the hard drive or cannot recognize the drive properly. Usually if that happens the splash screen will show and it will simply reboot. It also depends which version of windows ... E-Machines eMachines Desktop PC

Picture of where should the wires been attached in steering wheel


... Logitech Dexxa Steering Wheel Wheel And Pedals Set

No monitor signal and hard drive not spinning? (eMachines T3025)


Wiring diagram? Usually you just plug in the 4 pin molex connector. If its not spinning the HDD is damaged and needs to be replaced.Also I can tell you the Wires are Yellow=12v Black=ground RED=5v and orange=3.3v ... E-Machines T3025 PC Desktop

My external cabinet fan is not working ;it revolves only in the starting after that it doesn't revolve i changed it's power supply wire also but no use  i think it is having problem with the conducting wires  is their any way to repair it???


Sorry. I see you provided the information, eMachines T2682. Their website does not provide service manuals, but you can ask eMachines if the fan is thermally-controlled by sending them eMail at ... E-Machines T2682 (000002965) PC Desktop

Emachine W2047 No BIOS Start Screen


You can test the power button. Remove the wires from the power on pins on the motherboard. Momentarily jump the two pins with a small screwdriver. If the computer starts the power button is bad. If it still doesn't start then something else is wrong. ... E-Machines eMachines Desktop PC

5.1 surround problem


Hi Zamorano,sounds like your problem could be either with the wiring of your speakers, or the receiver. How long have you had them?check the wiring going from the sub woofer to the speakers- do you see any creases or damaged ( ... Logitech X-530 Computer Speakers

Emachine T2742 wouldnt start, new powersuplly installed green board light on but still no response. switched out ramstick,stiil nothing. switched out main processer still no.hard drive OEM is ok what else????????????? ive heard of similar probs this model,whts up????


First Pull cmos cell from motherbord for 10 minutes because sometimes low voltage of cmos cell creates this problem .After remove cmos cell from motherbord for sometime your bios settings goes to defaults.Then check.Also check that ... E-Machines eMachines Desktop PC

T-5010 Power supply issue


The voltage switch should be a small red switch, right below where the power cord plugs in. you will need a small screwdriver to switch it easily.\012if you are getting no power at all, i would also check all the wiring connections on the ... E-Machines T5010 PC Desktop

I have similar problem on an eMachines W1500


Thats your powersupply cable. look for a 4pin sloth on your mobo that looks kind of like that switch and plug it in ... E-Machines eMachines Desktop PC

T2958 motherboard connections


Guest Solution #5You are also an apprentice speller I see. I'll never know how you can just go online and display your illiteracy like that. Five spelling errors in one sentence. Didn't go to school or didn't pay attention did you? How can ... E-Machines (T2958) PC Desktop

Where do we find the display lid switch for a HP Pavilion dv9715nr ? we replaced a damaged hinge on this laptop first and now we cannot get a display.


Let me guess. Damaged Left hinge? HP had a recall for this problem, but the recall has lapsed as of May 31, 2009. ... PC Desktops

I have a T2958 and toof the face off. Can you


EMachines doesn't give out this kind of info, and I don't have one in the shop. eMachines also had the habit, of using a few different manufacturer's of motherboards. Intel, TriGem, MSI, Asus,and FIC to name five. Plus eMachines wou ... E-Machines (T2958) PC Desktop

I would like an internal view of eMachine T4150 to be sure everything is connected correctly


There's a bit of a toughie! eMachines doesn't like to give out this information, lyndapalimas, and I don't have one sitting in my shop.eMachines used four different motherboard manufacturers, to my knowledge. TriGem, Intel, FIC, and MSI. ... PC Desktops

No sound from altec lansing speakers, but have plenty of sound from headphones Not sure what speakers I have but they're around five years old. Also have subwoofer; could that be the problem? Hope someone can help! Ted


Without a model number of your speakers, this is going to be\015\012kind of generic. \015\012\015\012There are 2 major causes. 1) Damaged wire or 2) Bad wall\015\012Power supply or 3) Bad internal Power supply \0 ... PC Desktops

SPoradic faults when booting


This problem isn't easy to diagnose, but there are some things you can try to narrow down the problem. Do this at your own risk, but go into the bios settings and check your processor temperature. Take note that if there's a a feature to enable pro ... PC Desktops

Hp pavilion dv5-1002nr will not power up - HP Pavilion dv1000 Notebook


Let's run through a basic flow chart.1.Plug the AC adapter, (Charger), into the laptop.Is the Power LED light on, and the Battery charging light?[The Power LED light is on the front edge of your laptop, all the way ... HP Pavilion dv1000 Notebook

The screen will only display top half......bottom black


Might be the following:There are some (neon) lights behind the screen glass. If you can see a picture from the top, and on some angle the rest of the picture (in the bottom), that means you don't have a problem with your grapgisc card, dr ... HP Pavilion dv9000z Notebook

Monitor stays on for a few seconds then goes out


This problem is very often caused by dry electrolytic capacitors on the inverter board. If you have some skill with soldering you could try to change them. When buying new ones ask for LOW-ESR capacitors for switching mode power supplies (SMPS) and 1 ... Acer AL1711 17" Flat Panel LCD Monitor
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.8319 seconds