Having problems with your E-Machines eMachines Desktop PC ?

I have a emachine w2925 and when I tune it on. It just beeps and will not boot up


Answers :

If you have the manual, the specific sequence of beeps might tell you what the problem is. Beep codes vary by bios and manufacturer so I couldn't tell you what they mean without a maual for your specific model. Anyway, the 3 most common reasons are bad or loose memory or bad video, or bad power supply. You can try removing the power cord from the pc and open it up and reseat the memory but the other problems, you'll probably need a tech to look at to verify the exact fault.
Repair Help & Product Troubleshooting for E-Machines eMachines Desktop PC

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a emachine w2925 and when I tune it on. It just beeps and will not boot up


If you have the manual, the specific sequence of beeps might tell you what the problem is. Beep codes vary by bios and manufacturer so I couldn't tell you what they mean without a maual for your specific model. Anyway, the 3 most common reasons are b ... E-Machines eMachines Desktop PC

EMachine T3406 wont boot


Is there a post beep when the pc is switched on. check the memory if it is a beep beep beep sound , also disconect the hard drive, dvd drive, floppy, and any usb devices and see if it boots up. if that fails it does seem like the mother board, also c ... E-Machines eMachines Desktop PC

Emachine starts boot process but stalls, no beeps


Most likeley if you see something on the screen but it wont boot it is a mem problem, does it load bios, if so it is prob not memory ... E-Machines eMachines Desktop PC

On boot up the emachine now beeps every 5 seconds


Reboot with "F8" held down.\015\012you are only booting to bios and minimum disk software. This may give you an indication of your monitor or video driver status.\015\012\015\012If you can borrow another monitor from someone, that ... E-Machines eMachines Desktop PC

Replaced power supply on T2240 emachine now cant get onboard video" or any video,also tried PCI video card with no results. Need video to see if machine can boot


Unplug the computer for at least one minute. Press power button for 4 secondS while the power cord is unplug. Plug it back listen for beeps short and long beeps count them and refer to bios codes. If nothing happens remove everything from the mothe ... Intel PC Desktops

EMachine W3107 will not boot, no display.


Have you tried a different Graphics Card, looks to me like the onboard graphics card is at fault, there should be an AGP slot or PCI slot that you can plug a new Graphics card into then you should be fine... ... PC Desktops

Emachines notebook m5310 corrupted bios recovery


Solution 1: Boot-block BIOSModern motherboards have a boot-block BIOS. This is small area of the BIOS that doesn't get overwritten when you flash a BIOS. The boot-block BIOS only has support for the floppy drive. If you have a ... PC Laptops

Emachine w2686 no display when boot up


Couple things to check. First, check with different monitor. Their monitors are usually build by KDS and I think there was a bad series out there. Also check for any beep codes through speakers on startup, this can tell you bad ram or bad video out. ... E-Machines eMachines W2686 PC Desktop

My Emachines Desktop W5243 works sometimes and others just beeps


You might be having a minor dust particle situation going on. Take the memory out of the system. Get a can of air and blow out the slots on the motherboard where the memory would normally go. Then take the can of air and blow the connectors on bot ... E-Machines eMachines Desktop PC

Disabled video driver. Now unable to reboot emachines T5246


To reset bios with jumper settings: there is jumper on the board that has to be moved to the other adjoining pins, and then back. Hopefully it is marked. For sure check your owners manual, or google your mobo for the location of the jumper and exact ... E-Machines eMachines Desktop PC

Short but rapid beep code when powering up emachine


The beep code most likely is either video card or memory.\015\012If you have a video card or can borrow one that you know it works try it first, if that doesn't resolve your issue try the memory.\015\012You can take the memory out and hav ... E-Machines eMachines Desktop PC

Friend has a Emachine T1862 that won't start


May be the CPU fan is going bad. I hope it is that simple. ... E-Machines PC Desktops

Emachine running SLOW and Freezes - 1 year old


Here are some suggestions: First of all . Do you have an anti virus installed on your husband's machine ? Viruses can slow the machine and even kill it permanently ( so be careful) . Just install an anti virus and you'll solve the problem . If you ar ... E-Machines eMachines Desktop PC

Pc keeps rebooting, function keys don't work - E-Machines eMachines Desktop PC


Check that your keyboard lights flash briefly as your PC starts; that indicates your keyboard is Ok. If not, then check the connection or the cable. The kb lights usually blink briefly upon connecting to the power source. Try using another keyboar ... E-Machines eMachines Desktop PC

Monitor light blinks but no pic when booted up


I can try to help you,\015\012do you hear the boot beep sound?\015\012if you are not able to hear the beep sound then i suggest you to open the machine and check with the cmos battery if it is working or no.\015\012if your cmos battery is working the ... E-Machines eMachines Desktop PC

T2893 desktop did not power on when I hit the power button


If you can find someone that has the same model, that is the best way to make sure it fits. Some other motherboards will fit, but you may have to do some work to get them to fit. The best way would be to try to do some research on your particul ... E-Machines eMachines T3830 PC Desktop

EMachine Desktop Computer


This is most likely an issue with the powersupply being faulty, contact Emachines and tell them the error(as well as model and all that). They will then most likely send you a power supply that you can easily install yourself. Its just four screws in ... E-Machines eMachines Desktop PC

Emachine won't Boot past giant ''e''


\015\012\015\012\015\012\015\012\015\012Only way is to physically look at and identify the motherboard- if the PSU is ok, the symptoms point next to a MOBO problem, but start by removing memory & video see if that produces a diffe ... E-Machines eMachines Desktop PC

Emachine will not power up


By nothing else, from a technical standpoint this would mean literally nothing, the CPU fan, power supply fan, aux fan, disk drive not spinning up, etc. My experience with EMachines is their motherboards aint the best, have been known to take out har ... E-Machines eMachines Desktop PC

Not turning on, has power and everything


Do any of the fans spin at all, as though it's attempting to boot up? If not, then double check your power supply to see if it has a switch on it and if it does then make sure it's switched into the ON position. If so, then I would recheck the power ... eMachines T3604 PC Desktop

Emachine T2484 will not power up


Try to start it without any memory in it (RAM), if it beeps then you have bad RAM. If you have more than 1 piece of RAM then try one at a time and see if it will boot. If it doesn't beep and still doesn't turn on your CPU is probably the culprit si ... E-Machines eMachines Desktop PC

Emachine crash we had a power outage and my pc will not even allow us to go to the boot screen. The hard drive is making a beep every 2 seconds. Is the hd dead? Thanks a million! Lee


Yes, with that beeping sound that you're hearing from your hard drive is a sign of a bad hard drive , that's also the reason why the computer wont even boot because the hard drive is already bad, the best thing that you can do here is to get a new ha ... E-Machines eMachines Desktop PC

My monitor goes to sleep mode at startup & can't access safe mode


Turn the computer off, open the case and remove the RAM. Does the computer beep when you turn it on with no RAM? If not, your motherboard is dead. If your computer beeps, turn it off again and try putting one stick of RAM in. If the co ... E-Machines eMachines Desktop PC

PC won't boot after changed BIOS memory settings


With all that you've done, you might have worsened your PC mobo's condition. Now try to remove the processor and memory then PLUG it normally to the power outlet and see if the led in the mobo lights. After 3 minutes, unplug it and reseat the rams an ... Toshiba Satellite A135 Notebook

Power on emachine T6420 and moniter is blank. The moniter soon loses contact with the computer. The fan run and power is OK there is no beep code.


If you mean after the computer performs the self test the screen goes blank and stays blank, eventually turning off you are having a hard drive problem. When the computer boots you should see an E-Machines logo and/or a self test on the screen. Tha ... E-Machines eMachines Desktop PC
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.4687 seconds