Having problems with your E-Machines eMachines Desktop PC ?

A power diagram for restoring power for a emachine

\015 Do you have a diagram for the emachine to get power?I have 3 wires coming from front panel that needs to be plug into the motherboard to restore power\015

Answers :

Hi there if you look real closley at the wires they are labled such as (pwr)led (reset) (hdd led )
(remote switch this the power for the computer) ect ect now look real closley and you will see the same markings on the edge of the board by each pin that they go to.. or you can also contact e-machines tech support and they will be able to help you out more if needed
best regards mike
Repair Help & Product Troubleshooting for E-Machines eMachines Desktop PC

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

A power diagram for restoring power for a emachine

Hi there if you look real closley at the wires they are labled such as (pwr)led (reset) (hdd led ) (remote switch this the power for the computer) ect ect now look real closley and you will see the same markings on the edge of the board ... E-Machines eMachines Desktop PC

EMachine no power

Ok for a start the power switch is not green and white that is the power led, you need to look for a red and black wire normally marked on the connector and motherboard as pwrsw or pswitch.\015\012if you believe it to be the switch unplug the c ... E-Machines eMachines Desktop PC

Emachine t1840 wiring diagram power switch wire to mother board ?

Because there are so many different case and motherboard combinations\015\012sometimes it can be difficult following the instructions for connecting\015\012the front panel, USB header and audio header.\015\012\015\012Below is a few generi ... PC Desktops

Need large disc support for old emachine, flash bios? or try restore cds?

Hi,\015\012flashing a bios, can render your machine/motherboard useless.\015\012You should always ensure any bios download is from a trusted source. if you experience a power failure, or an incomplete bios file. your computers as good as ... E-Machines eMachines Desktop PC

Need correct MOB location for power switch on emachine W3410.

What kind of motherboard did you change..?try to search in the internet.. just type the name of the board and including the diagram.. sample.."ASUS MOTHERBOARD POWER DIAGRAM"... ... PC Desktops

Need wiring diagram for emachines t2200 motherboard

If you are replacing the power supply and it has 4 pin 12v conector and your motherboard doesn't, just disregard the 4 pin plug. The 20 pin conector will supply sufficient power for the processor. Many of the older motherboards did not have a separa ... E-Machines eMachines Desktop PC

No power on my emachine

The power supply might be okay but the system board could be bad and not turning the power supply on when you press the power button.On this page:http://www.helpwithpcs.com/courses/power-supply-basics-inc-pinouts.htmabout midw ... E-Machines eMachines Refurbished EMA SYSTEM BOARD MODEL T2984 eMachines (102257) PC Desktop

T1100 emachine - restarts at windows logon screen

Have you made any hardware/software changes lately? If answer is no, reboot the pc and hit F8 a couple times. This will give you a list of options. Use your arrows and highlight last known good configuration and hit enter. See if your pc boots ok. If ... PC Desktops

Emachine t2742 I also have a wiring problem!

Gtater,It's ironic that you ask me this question today-- i am just now carrying in another eMachine computer to fix. Anyway, unfortunately I do not have one that is the same model as yours (T2742). However, I did some quick research and found t ... E-Machines eMachines Desktop PC

Cpu upgrade , please help

Tech-gu818, When looking to see what processors a computer will support, try to find out what motherboard chipset is on the motherboard, and the processor socket.The motherboard chipset is the;1) Northbridge chip2) ... E-Machines eMachines Desktop PC

Emachine Won't power up

Just because it has a SATA plug doesn't mean you'll need it- especially if your machines a few years old. If your hard drive doesn't have the sata connections, then you probably won't use it. \015\012 As to why it still won't power up- how did ... E-Machines eMachines Desktop PC

EMachines Power Switch

Hi,Rather than hunt for a diagram, take a metal conductor and short out the prongs two at a time until you find the two that turn on your PC. It is 100% safe to do this as you CANNOT damage the motherboard by shorting out the wrong prongs. ... E-Machines eMachines Desktop PC

Motherboard Config Emachines T2984

I made this diagram, hope it helps! ... E-Machines eMachines Refurbished EMA SYSTEM BOARD MODEL T2984 eMachines (102257) PC Desktop

Emachine t2984 - need to diagram to install power & hard drive

There is 2 main cables you have to worry about to feed power to the system. One looks like a big rectangle block with a mess of wires attached. Make sure he is hooked into the system. Then if its an newer unit you will find a plug that has square loo ... E-Machines eMachines Desktop PC

Emachine T6420 Motherboard??Turns off light flashes,very slow

This could be any number of things. Try removing and reseating the hardware - video card, memory, processor (power disconnected of course). The symptoms you describe could be cause by a faulty motherboad component, video card drivers, other operati ... E-Machines T6420 PC Desktop

My emachines EL 1200 desktop stopped working during bad storm

You can try to reset the computer by removing all power sources and letting it sit for a time. Then powering it back up and see what happens. That's called a hard reset. \015\012I am guessing that the storm surge damaged your motherbo ... PC Desktops

Front panel leads Emachine model T2862

E-machine model T2862 pin-out for the 10-pin front panel header is screen-printed on my Emachine's motherboard, but is so small and far away from the actual pin location, that it is likely being overlooked. If looking into the computer case from the ... PC Desktops

Restore disks i need to restore my compouter, not the one i am on now but another one its and emachine t2682 it runs soooo slow and popups keep opening non stop where you cant do anything, is there a way u can ship me the restore disks

My t2692s power supply blew and took the mother board with it, I replaced the mb with a biostar and used the restore disc from a t3508. It came up that my Windows software was not a legal copy, but gave me a toll free number to call Microsoft an ... E-Machines T2682 (000002965) PC Desktop

Powerbutton connection wires were disconnected from motherboard

Look in the manual there is a diagram and pin connections for each wire. ... E-Machines D2046 PC Desktop

Had virus so i went in to reboot by deleting all data. ran all 5 cd's and as was reinstalling it kept freezing up so would have to hold button in to restart. now all i get is a blank or blue, black, or blue screen w/ black lines ,that is if i can get it up and running. now it won.t start at all but the fans come on

Well, if you cannot get anything to happen except for hearing the fans spin up, then my guess is that the motherboard is probably bad, which is a fairly common thing for eMachines. You should at least get the POST (power on self test) screens, usuall ... PC Desktops

I want to do a system recovery on a EL1200 emachines? Could someone tell me how to do this?

Hi,\015\012\015\012I work with these machines every day, this model was designed after Acer bought out Gateway(who owned Emachines).\015\012\015\012If you provide me an email address I will send a copy of the recovery disk cre ... E-Machines eMachines Desktop PC

My emachine computer T1105 just stop working when i insert the restore CD it say "ERROR 0200: FAILURE FIX DISK 0

1. Make certain the caqble connecting the CD drive and the motherboard is secure. power down the computerremove the power cordopen the caseGROUND YOURSELF ON BARE METALtrace the wide ribbon cable connecting th ... PC Desktops

Emachines 2792 i have an emachines t-2792 and it keeps restarting itself before windows has a chance to load. it does the post fine and everything. i have tried a windows xp sp2 cd and it kept comming up with its missing files. then i tried the restore software that came with the computer and it seemed to take that but it still won't load windows. i get the xp simbol and then a flash of a blue screen and its restarts.

Pull the power plug as soon as the emacines logo comes on\015\012and if that doesn't work pull out the power as soon as the first windows logo screen comes on. it should then come on and give you the option to start in safe mode or regular mode ... E-Machines T2792 PC Desktop

Emachines t2865 power led diagram

The header connections that you are looking for are on the edge of the motherboard near the battery. Look for a group of gold contacts sticking straight up at you. The silkscreen tells you which header are for what light or switch. You will see one t ... E-Machines eMachines Desktop PC

Emachines t3830 I need the schematic for MB I umployed the wire for the push bottom without looking at the way they were plug. Now I do not know the correct aligning of the push bottom wires.

If you look at the motherboard there is usually a diagram labeled "FRONT PANEL HDR" that will tell you which pins are for: HDD LED, PWR LED, RESET, PWR ON. etc. The chart / diagram may be a few inches away from front panel header.the fol ... E-Machines eMachines T3830 PC Desktop
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.5385 seconds