Having problems with your E-Machines eMachines Desktop PC ?

Power on .message on monitor saying no signal

\015 Was doing disk clean and disk defrag then monitor went off .have tried to restart but nothing.\015

Answers :

Hi
\015\012first check your monitor cable, remove it and fix it again.
\015\012even if monitor dose'n start then open your cabinet and inside it there is one auxilary cable( having 4 pin connector)if wire is removed then fix it on motherboard near cpu fan n ur problem will be solved.
\015\012thanks for a chat.
\015\012any more problem then you can ask me.
\015\012bi.
Repair Help & Product Troubleshooting for E-Machines eMachines Desktop PC

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

NO SIGNAL What do I do?


These messages are normal when the computer truly goes into suspend mode or loses the video signal (such as when the computer is suddenly turned off).If the monitor displays any of these messages when the computer should be displaying vid ... HP PAVILION A6230N DESKTOP PC

Lcd monitor power light flashing with no img. seems 2 be frozen


The display is in safe mode and you will need to reset the display to get the display out of the safe mode. There are 2 different model revisions. Please choose the method that will match your revision. Depending on the revision of the monitor, one ... Planar PL1910M (Black) 19 in. Flat Panel LCD Monitor

Monitor screen begins as computer is booting up and then screen goes black. Message says there is no signal.


If the power light dims or changes color after the no signal message comes up, that means the monitor went to sleep.While the monitor is plugged in and on and the computer is also on, Try unplugging the VGA cable from the monitor. wait 30 secon ... ViewSonic VG2230WM LCD Monitor

Osd lock in my LCD


Check your switchers resolution settings .....\015\012You might have to change your resolution settings....\015\012 \015\012This solution is for AOC Monitors...... ... X-10 LM929 19IN LCD 12X10-.294MM SPK BLK

Going to Sleep


Due to the power surge, it is highly possible that the monitor was given a boot by your computer on it's way out.\015\012\015\012This will short out a very small transistor inside the monitor on the video board and in turn, then monitor c ... HP Pavilion F1903 19" Flat Panel LCD Monitor

Mitsubishi diamond pro says "no signal"?


You have tried the monitor on more than one known good computer, yes?\015\012\015\012I believe about 4" inside this monitor in the back the vga cable or connector connects to a board with an in-line connector. Can you see if this connect ... Mitsubishi Diamond Plus 100E Monitor

Computer monitor comes on for 1 seconds, flashes "analog power save mode" and then goes black.


Most monitors will say "Power save mode" when they can tell through residual voltage that the signal lead is plugged into a machine, but there's no picture being transmitted. The four states of a monitor are:* Off entirely.* Switch ... PC Desktops

Can't find video signal


If screen says "Signal cable not connected " all the time till power led switches to Amber chances are monitor is ok and problem is with graphic card or cpu.Connect to Known working CPU and confirm that monitor is the problem.\015\012If same pr ... BenQ FP731 17" LCD Monitor

My tower had a virus/trojan horse AND IT DOES NOT START OR REBOOT


Too complicated when I read your post. Why not take it easy, and sort your problem step by step. Ok you said you have a virus or trojan. Why not try other free antivirus? Try to use Avira free with malwarebytes antimalware in combo. Its lite and a ki ... PC Desktops

LG 2542T goes dark after showing "analog power saving mode" message


If it is saying analog signal power saving... I am wondering do you have it hooked into you computer with the white DVI cable?Is there an option on your monitor to switch modes? Analog-Digital? If you are using the white DVI cable to hoo ... LG L1717S-BN 17" LCD Monitor

I turn on my computer but my monitor says there is no signal


Hello, try to unplug the cables on your desktop, then plug it again, sometimes its loose, or sometimes the power supply on your computer is not functioning properly. ... PC Desktops

Power save mode


Yes, you arent getting a signal to your monitor from your video card. Try replacing. If its onboard then the Mainboard may be bad. These machines are known by Dell to go bad and is covered under warranty, provided you still have it. \015\012 ... Dell OptiPlex GX280 PC Desktop

Black screen, blinking power light, no signal


Its a software bug in the monitor. Mine has done this since new. There is a race condiction between the monitor starting and Windows Starting. If the monitor starts faster then it thinks that there is no DVI connection and it will then revert to V ... ViewSonic VX924 19" LCD Monitor

My display don't have light


Disconnect the unit from the computer.\015\012Disconnect from power source.\015\012Let the unit sit for a few minutes.\015\012Plug the unit into the power outlet.\015\012Push in the power button and if you get a message on the ... Samsung SyncMaster 940MW 19" LCD Monitor

Dell ultrasharp blinks on and off


It could be a setting problem, power saver setting, or a mode that the monitor does not really support - things like refresh rate - or actual hardware.\015\012\015\012Easiest way is to borrow another like monitor, and say another video co ... Dell UltraSharp 1800FP 18.1" LCD Flat Panel Monitor

Nothing comes up on the screen


The monitor connected to the system is set to receive video signals from the DVI port on the video card and it is not getting a signal.\015\012\015\012Possible Causes:\015\012\015\012Monitor is connected via VGA ... Dell OptiPlex GX280 PC Desktop

No composite input signal


`Hi,\015\012 If the monitor is making the noise , the monitor circuit baord has gone bad.\015\012If you have purchased the monitor on a seprate order from dell it would be covered under 3 yr warranty. If the same has been bought with th ... Dell UltraSharp 1907FP 19" LCD Monitor

Black screen with message about no input signal


Might be something wrong with your monitor's data cable ... Sony SDM-HS95P/B 19" LCD Monitor

Monitor goes into power saver mode


Take your Agp card with you to the shop. You do not need to go through Gateway, but there are serveal formats of AGP regarding the voltages.\015\012\015\012By the sounds of it you have the newer version of AGP so finding a replacement car ... Gateway 500 X PC Desktop

I have just set up new desktop Acer. Error message: No input signal.


Check the website for drivers. But it seems to me that there is another problem most computer boot up no matter what screen is hook up. have you tried any other monitors ? If you have and the work im not sure what your issue is but i would say that ... Acer Aspire™ T180 PC Desktop

My monitor when powered up gives me a no input signal for VGA and DVI and then goes into sleep mode after 15 seconds. I plugged in a second monitor and have a no signal message too. Should i replace the video card or has the monitor locked itself out. Please advise....Best Regards Beth.


Hey BethSounds like you are in a bit of trouble!Based on what you've told me, it looks like it might be a video card fault. However, a few things to check first are..Make sure the VGA & DVI are secured tightly ... HP f2105 21" LCD Monitor

Dell 1800FP, no signal found (analog). Green LED on, get message


Check if your signal cable is properly connected to your system unit and make sure that non of the pins of your signal cable is broken.if any of the pins are broken,try and change the whole signal cable and re-connect it again\015\012after foll ... Dell UltraSharp 1800FP 18.1" LCD Flat Panel Monitor

'input not supported'


All I can say is WOW! I have been using my pc with my monitor for months and I was installing a new printer and must have wiggled something loose, and all I was getting out of my monitor was "INPUT NOT SUPPORTED." So I came to this forum, and low a ... Acer AL1916W 19" LCD Monitor

I plug in the monitor and the lights light up but there is nothing on the screen


Hello there andy_sellard.\015\012\015\012Here's your GEEK-steer ...\015\012\015\012To be clear, what I'm hearing you say is, the monitor is NOT connected to a functioning PC during your procedure. If this is the situation: ... HP Compaq 2025 (Carbon, Silver) 20.1" LCD Monitor

I live in Seattle and have an Acer V193B that 'went dark' when I hot-pluggged the VGA connector into my laptop. I *assume* the problem is the chip that buffers the VGA lines is blown. (I know the cable and laptop VGA are not the problem.) The monitor has power (power button glows orange), there is just no video display. Is there any chance that I can get this repaired w/o spending more than the monitor is worth in shipping and repair costs?


First, to check the monitor.\015\012Disconnect the input signal from the computer.\015\012Turn off the monitor and unplug from the A/C source.\015\012Allow the monitor to set for a few mi ... Acer V193 B LCD Monitor
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.9633 seconds