Having problems with your E-Machines eMachines Desktop PC ?

EMachine Floppy Drive Flopped??

\015 EMachine T1090 Floppy Drive Just quit...Device Mgr, Says that it and the Controller are working fine, Unfortunately when I put in a Diskette, and Right Click to Format. I get: ''Insert Disk into Drive A'', No ''On-Light'' either..Have UnInstalled Both Drive and Controller and Re-Installed, still does the same thing. Have UnPlugged the Connections, Cleaned, and Plugged back in, still Nothing... is it Toast??\015

Answers :

If you are comfortable with opening your machine, you should power down, open case, disconnect the eide cable and power cable from drive. Reconnect both, close case, and power the machine back on. Allow Windows to recognize as new drive.
You could also try updating the drivers under Device Manager as well.
Repair Help & Product Troubleshooting for E-Machines eMachines Desktop PC

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

EMachine Floppy Drive Flopped??

If you are comfortable with opening your machine, you should power down, open case, disconnect the eide cable and power cable from drive. Reconnect both, close case, and power the machine back on. Allow Windows to recognize as new drive. You co ... E-Machines eMachines Desktop PC

Where does the cable labled P7 go - E-Machines eMachines Desktop PC

Hiya,\015\012\015\012I have an image for you to look at, and I will need confirmation that this is or is or is not what you are giving reference to.\015\012\015\012 ... E-Machines eMachines Desktop PC

Yea sorry, forgot that tid-bit of info. It,s the W3118 eMachine / Gateway FIC K8MC51G

This issue can be caused by any of the below reasons.-Corrupt boot files on the computer.-Settings for hard disk drive are not correct.-Floppy diskette or CD in computer causing issue.-Boot devices not set properl ... E-Machines eMachines Desktop PC

Emachines notebook m5310 corrupted bios recovery

Solution 1: Boot-block BIOSModern motherboards have a boot-block BIOS. This is small area of the BIOS that doesn't get overwritten when you flash a BIOS. The boot-block BIOS only has support for the floppy drive. If you have a ... PC Laptops

How to remove ibm thinkcentre p4 3.0 motherboard

This is the link to the IBM ThinkCentre S50-8183, Hardware and Maintenance Manual,http://www-307.ibm. ... IBM ThinkCentre S50 8183 - P4 3 GHz (8183D9U) PC Desktop

Emachines t2542 i've had this computer for about 4 years now and recently its been acting up, when its just running its kinda loud, also i usually keep my computer in stand by and when i came home one day i find the light under the power button flashing rapidly and a weird ticking sound that went along with the flashing light. i moved the mouse, usually it brings the computer out of stand by, but no response. i kill the power to the computer and wait a little bit, plug it back in and the flashin

Assuming you didnt leave a floppy disc in the drive causing windows to boot from floppy, if you have disconnected the drive you have to tell the bios not to look for the drive.\015\012\015\012Press F2 or Del while the pc is booting up and in the firs ... E-Machines eMachines Desktop PC

I am trying to replace the hard drive in emachine 500is. Now the computer will not recoginize the cd rom to read the windows xp set up disk.

Go into BIOS Setup, and in Boot Order, change the first boot device to CDROM.How?To go into BIOS Setup you start tapping either the DELete key, or the F2 key, ->Right After you see the eMachines logo. If you miss this window of o ... PC Desktops

Need to find the NTLDR on my emachine I tried the recovery disk option to reset the reboot option - and was still unable to correct the problem. Are you aware of another solution? Thank You

A couple of things.\015\012\015\012If the system has a floppy diskette drive, ensure that no diskette is in the drive. (I know it sounds simple but ...)\015\012\015\012If no floppy drive issue, then run diagnostics on the hard ... E-Machines eMachines Desktop PC

My emachine freezes after it boots up. I had

I must say at the front that you seem to have the machine looked at professionally and received advice. They couldn't fix it ... I'm not sure I can build on that diagonosis. I do have a few ideas, however. This is a case where the messenger is tel ... E-Machines eMachines Desktop PC

Blue screen error, no cd or flop drive, need usb reboot if poss

Obviously you need an XP CD--see if you can borrow one from someone. \015\012If you can, start the computer, press F12 to get the boot menu, and\015\012when it starts from the CD wait until you are prompted to choose an\015\012option. Choose R to re ... Dell Latitude D600 Notebook

When I turn it on, only the fans run. I cannot hear the hard drive run and the hard drive light on the bezel is solid yellow

EMachines were designed to be Budget computers. As such the company used cheap Power Supply's. Cheap components within the power supply have failed. The power supply only has enough power to light, lights, and spin fans.Solution is to rep ... E-Machines T6216 (827103077834) PC Desktop

Emachines T3882 desktop w/one cd-dvd combo drive[no floppy]

Hi, now the screen is blank[black]with a blinking cursor and will not accept any commands. No words or error messages, only a blinking cursor. I tried different CD's; Window XP, Hiren's, Maxtor MaxBlast, Ultimate Cd, and it stays on the blinking curs ... E-Machines eMachines Desktop PC

EMachine T3406 wont boot

Is there a post beep when the pc is switched on. check the memory if it is a beep beep beep sound , also disconect the hard drive, dvd drive, floppy, and any usb devices and see if it boots up. if that fails it does seem like the mother board, also c ... E-Machines eMachines Desktop PC

Unmountable boot volume

Hopefully you have a windows installation cd or a recovery cd. If you do then you need to install it into your cd rom drive. Reboot the computer and you will see a message that says to press any key to boot from CD. If you do not get this message and ... eMachines EL1600-01


When you first start the computer press the f 8,(that is the key most use to get into the bios). Set everthing to the default except the drive sequence which you want the cd first.\015\012If I am not correct,then  go to the support webpage and d ... E-Machines eMachines T3830 PC Desktop

Connections i have a emachine t2882 i need to know how the power supply plug in to what and where

The main connector to the power supply has to go into the motherboard. Its a rectangle shapped male connector that is on the end of the power supply that plugs into a rectangle female shaped connector on the motherboard. There might also be a short ... E-Machines eMachines Desktop PC

Emachine t3958 Hi, I turned off my t3958 by pushing the power button and now it want come back on. I ohm the switch, not sure what it should be but it 0 out. I pulled out the mother board and inspected it, nothing looks or smells burnt. With the mother board out I plugged the power supply in to a outlet and one fan started running but only for a second then stopped. I then waited a few minutes plugged it back in and it did the same thing and if I unplug and then plug right back in again it does

First check to see if a drive died. Unplug all the drive Floppy, hard and dvd or burns. I have come across many time that a drive will die and keep motherboard from booting. Being that you say you get a green light on the motherboard shows that the ... E-Machines eMachines Desktop PC

Network drives i need 2 download network drives for my emachines 4210!!! i have a modem which works but cant connect to the internet until i install network drives! please help

Ask a friend to download them for you and put them on a floppy or USB stick. Otherwise you are stuck. ... E-Machines eMachines Desktop PC

Eliminate all info on emachine PC

There's an excellent tool I use myself called KillDisk that is free, just download it and copy it to a bootable floppy disk, then use it to entirely wipe your whole hard drive, it just takes a few hours depending on your computer speed and drive size ... E-Machines eMachines Desktop PC

Computer starts up until it gets to e-machine logo

I would start by unplugging all devices, drives from the PC. Printers, Cameras, iPods. The only thing that should be plugged in is the keyboard, mouse and monitor. If that yields no result, it's time to open the case and disconnect your optical (DVD/ ... E-Machines eMachines Desktop PC

I am looking for a wiring diagram for my emachine front power switch

Power Supply Types \015\012\015\012There are two basic types of power supplies. There are AT power supplies, which are older and in older computers, and ATX power supplies, which you will find in virtually every new c ... E-Machines eMachines Desktop PC

Emachine startup problems

Good afternoon, nooks!You an try taking it down to barebones and see what happens.\015\012By bare bones, I mean to disassemble to the point that you only have the power supply, motherboard, and the display hooked up. At this\0 ... E-Machines eMachines Desktop PC

Need to know what parts compatable to ATX-1523D for an emachines T-1090

It's a Small Form Factor power supply. 4.9 inches Wide, 2.5 inches Tall, and 3.9 inches Long.Put's out a maximum of 150 watts, (Supposedly)Has the following power cables;A) (1) 20-pin ATX main power cable: ... E-Machines T1090 PC Desktop

Emachine won't Boot past giant ''e''

\015\012\015\012\015\012\015\012\015\012Only way is to physically look at and identify the motherboard- if the PSU is ok, the symptoms point next to a MOBO problem, but start by removing memory & video see if that produces a diffe ... E-Machines eMachines Desktop PC

Cd/dvd rom my cd/dvd rom does not work i opened the computer and saw that the "cable" conecting it was ripped in places. is this the problem i have an emachine t1090 that i am trying to get running so my son can play games on it. windows xp. also there is another "cable" in there that one end is not attached to. it says motherboard and slave on it. can i use that one

Computers typically have 2 IDE connections on the motherboard. 1 Primary, and one secondary.\015\012\015\012Your HDD ( Hard Disk Drive) should be connected to the primary as MASTER.\015\012Typically the CD ... E-Machines T1090 PC Desktop
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3551 seconds