Having problems with your BenQ FP567s 15" LCD Monitor ?

Monitor displays no signal as soon as i boot into win xp

\015 I'm using it as an external monitor for my dell inspiron 9300 because my screen is broke, but, every time i boot in normal mode, it comes up saying "no signal detected" I'm using the vga output\015

Answers :

You may have to put the laptop in presenter mode, which tells it to use the attached monitor. There is supposed to be a key on the laptop which does this, its normally the FN key with CRT/LCD (F8). You can also do it via screen properties but since your screen is broke u'll have to use the key shortcut.

If that doesn't work, then your video card may be bad and you'll have to change it.
Repair Help & Product Troubleshooting for BenQ FP567s 15" LCD Monitor

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

PC or monitor, signal problems


Your monitor is telling you it's on it's last legs..either that or your compaq has a bad video section. either is more vital than a video cable being loose. ... PC Desktops

Monitor displays no signal as soon as i boot into win xp


You may have to put the laptop in presenter mode, which tells it to use the attached monitor. There is supposed to be a key on the laptop which does this, its normally the FN key with CRT/LCD (F8). You can also do it via screen properti ... BenQ FP567s 15" LCD Monitor

The power light glows solid, but there is no display. The screen doesn't come on at all


If the symptoms start from the moment you turn you PC on, and you don't even see the POST messages as it boots, chances are your monitor has given out the ghost. Time to replace it. \015\012However, if you see some text lines and logos as soo ... Samsung SyncMaster 931B 19" LCD Monitor

No picture or power green light just blinks - Sceptre X9G Komodo II (Black) 19 in. Flat Panel LCD Monitor


Carrizosas, Tell me more. How old? Approx. total "ON" hours of use? Did it display a "bright, crisp, full color text and graphics and pictures the day before? Does this unit have a lay on floor "BLACK BRICK" ac to dc supply, or only a 3 wire line cor ... Sceptre X9G Komodo II (Black) 19 in. Flat Panel LCD Monitor

Input Signal Out Of Range


Some monitors have low resolution, that if it doesn't support that resolution then you'll expect an "input signal out of range" message on screen. try to boot on "safe mode" if it works then you have to lower your screen resolution at "display proper ... HP Pavilion F1523 15" LCD Monitor

Acer AL1716 (black) - Drops to No Signal -


If you google this problem. you will find that acer monitors have this problem. They pretty much all do. Its an annoying problem but there is no fix. The only way to remedy it is to unplug the monitor and plug it back in when you get this error. pret ... Acer AL1715 (Black, Silver) 17" LCD Monitor

Monitor won't stay on. Error message comes up that says "no input signal", then monitor goes out.


Problem with the monitor, monitor cable, or video output. For monitor, if you have more than one input, make sure it's set to the correct one. Try a different cable. Try a different monitor. Check your video card settings--if you see the BIOS boo ... HP PC Desktops

Dell E228WFP Monitor failure


To me, that's an XP driver issue. If the screen turns on at all, then goes dark during XP boot, that's nearly a ringer for drivers. Out of range on the Hz? Tried booting in safe mode to see if it loads with standard win drivers? That migh ... Dell E228WFP LCD Monitor

Monitor falls asleep during/after startup


... HP Computer Monitors

"No signal detected" when LCD connected with DVI-D Cable


Thank you for providing your configuration details.\015\012You have failed to specify wheather or not your LCD Display is under Warrenty.\015\012\015\012Perhaps these simple trouble shooting procedures will get the job done.\0 ... BenQ FP71E 17" LCD Monitor

Please can anyone help me i have recently upgraded my monitor from a xerox 19'' to a samsung 23'' syncmaster now with the monitor in standby i turn on my acer t180 and the green light in the on button dosent light up an the monitor wont detect a signal if i turn off both pc and monitor then turn the pc and then the monitor everything works fine in this pc i am running a xfx 9500 gt graphics card and have the latest drivers for the card and monitor so why should this be. i know its only a little


I assume you are running windows. First off you need to boot into safe mode by pressing F5 repeatedly as soon as you start your computer. Select the option for safe mode. Once you are in then you need to go to the device manager. Click on the run opt ... PC Desktops

Screen will not display


Hi,Have you ensured that your display card driver AND correct monitor driver is installed. This is to make sure that your display card only generates signals that your Acer monitor is capable of handling. If you do not have the driver CD for yo ... Acer H233H bmid Monitor

No signal on first boot


I think is a power supply problem,, ... Nokia 445 Pro 21" CRT Monitor

Princeton Digital VL1716 Monitor "No Signal Message"


Roxio Changed Your display settings on the dual display.\015\012\015\012Right Click on desktop>goto Prefences> \015\012\015\012You should see both monitors indentfy the one and change it to a lower resolution. ... Princeton Digital VL1716 17" LCD Monitor

Mag monitor doesn't display bios post


The BIOS is sending the display information to the monitor but, when you turn your PC on, the LCD will be sleeping and it will take 1~2 seconds to wake up when receiving the display signal. The monitor is working and even if the BIOS messages aren't ... Computer Monitors

Power failure issues


Father2gabe, Try this! With fully booted KNOWN GOOD pc displaying the win-desktop, reconnect suspect bad monitor to PC. Then and only then turn on the monitorand note what happens on screen. What happens if you point a bright flashlight (torch) at 2- ... Balance CM2017 17" Monitor

Pc wont read monitor


If you look at the monitor there will be an led light on the front that is always orange or yellow when the computer is off but still connected to the monitor. This led will turn green when the computer boots up, sometimes even showing a "no signal" ... HP PAVILION A6230N DESKTOP PC

Screen comes on says Acer then No Signal, and goes out. if shut power off and then back on get same result.


This means the monitor believes it's not connected to the computer. Verify the cables first of all. Then try booting in safe mode (F8 key at PC startup) in order to verify that the PC is sending data to the proper video port (you might have a dual VG ... Acer AL2223W 22" LCD Monitor

Problem with the monitor


Hi,The three boxes represent the built-in diagnostics of the monitor. The letters G is green, B is blue and R is for red, the 3 color guns of the picture tube of your monitor. The words "Self Test" indicates that it is in diagnostic mode ... Compaq FS7550 17" CRT Monitor

No display on SyncMaster 710N


I used 2 resistor of 100 ohms (1/8W) to make one of 50 ohms. Like others instruction, just put the 50 ohms resistor between pins 5 and 6 of this chip and the problem is solved. ... Samsung SyncMaster 710N 17" LCD Monitor

HP (dv2000) laptop will not boot up at all


It appears to be a video card/mainboard problem very common with the symptoms you have described. Try to connect the laptop to an external monitor (see the associated buttons too). No video signal on the external monitor could indicate a damaged vide ... HP Pavilion dv2000t 14.1" Notebook Laptop PC (Intel Core 2 Duo T5500 1.66 GHz, 1GB RAM, 100GB HDD, D... PC Notebook

Ibm xseries 235 eserver....all of a sudden stopped booting...it was set up through a kvm swtich, the kvm detects a signal and lights up the apprpriate port, yet nothing is displayed on the monitor. disconnected from kvm, connected directly to a monitor, and still no signal....only error light is indicating a HDD problem, that has never failed to put something on the display before, im kinda stuck on how to troubleshoot....i know the drives are good, i guess it could be a LSI adapter problem, but


The drives were working right before it rebooted....it booted into windows prior to this. i shut it down to install another drive, turned it back on and nothing...not even a post screen. i removed the hard drive from the scsi controller and it stil ... IBM eserver xSeries 235 8671

I've been trying to use s-video cable to connect


\012\012At the rear or side of the PC there should be either or both of a 15 Pin DIN Plug, HDMI socket. or a Yellow RCA or 4 -7 pin DIN. Now IF these are present then YES you can connect to a TV. Now some TV' ... Acer Aspire 3690-2196 Notebook

I have a dell inspiron 9300 with win xp pro for an os, my lcd screen is broke, so i took it off completly. now i am trying to hook up an benq fp567s monitor through the vga output. it will get me as far as desktop screen just after boot up. & most of the time it goes in to sleep mode before start up is complete. the screen suddenly displays "no signal" ?


Many people have noted two primary failures with this monitor. i have a couple time-saving troubleshooting tips, which actually apply to mostly all electronic devices. first, of course, bulging electrolytics [capacitors] should be considered suspect. ... BenQ FP567s 15" LCD Monitor

I have this monitor hooked to my PC ATI 7500 graphics card with a DVI cable. When the PC initially boots up, the monitor display is blank - it does not display the boot-up messages until the MS Windows display screen actually comes up. So, it is not possible to boot into "safe mode" or other "dual boot" OS option. Is this normal, or do I have a problem with this particular monitor?


This is normal. Your monitor has a VGA hook in for regular definition. What it is doing, the monitor always by default looks for the VGA hook first. On my desktop it does the same thing until it finds a signal on the DVI. ... Samsung SyncMaster 940MW 19" LCD Monitor
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.8398 seconds