Having problems with your Acer X193W LCD Monitor ?

No Signal and BIOS troubles - new video card

\015 I tried to install an ATI Radeon 4650 video card, and have been having troubles from the first time I put the card in. I am using an Acer Aspire am1201-b1603a with 3gb ddr2 memory, 320 gb sata hard drive, etcetera, etcetera. I have tried jumping the CMOS to reset it, removing the CMOS battery to reset it, and everything else that others suggested. Right now, with no video card installed but the stock one, I am able to bring up the BIOS screen (which says "date/time wrong"). I change the date and time, save and exit, then try to enter Windows Vista via "Start windows normally". From here you see the windows loading bar (the green one with the vista logo on a black background), and then you see "No signal" and the monitor goes to sleep. What do I do?\015

Answers :

Try using the onboard graphics instead and remove the graphics card. then uninstall all the graphics card drivers and software and reinstall again. make sure you install 32bit or 64bit depending on what your operating system is. you can find out if it's 32 or 64 bit in the welcome center of vista.
Repair Help & Product Troubleshooting for Acer X193W LCD Monitor

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Faulty motherboard? Hi, my PC has an ansus p5vd2-mx motherboard, intel duo core processor, pci express slot, gforce graphic card. I upgraded the graphics card for faster secondhand one which resulted in loss of video signal and 1 long and 2 short beebs from the BIOS ( faulty graphic card? ) Replaced the original graphic card but still getting the same error beebs and no video signal. The fan on the graphic card is still working so it must be drawing power from the pci express slot. My question i


Bullnosestep\015\012\015\012\015\012It is possible that the new (secondhand graphics card) was faulty and sent an incorrect voltage to part of your motherboard (frying it). However in my experiance it is not likely, I have installed ... PC Desktops

No Signal and BIOS troubles - new video card


Try using the onboard graphics instead and remove the graphics card. then uninstall all the graphics card drivers and software and reinstall again. make sure you install 32bit or 64bit depending on what your operating system is. you can find out if i ... Acer X193W LCD Monitor

Need help with new AGP video card for T3092 E-machines desktop


You should go in to your start-up bios and ensure the on-board video is disabled. The computer will auto-detect the video card but if the on-board video is enabled then it will cause a conflict. Let me know what happens. Good luck. ... E-Machines eMachines Desktop PC

Dell 1600SC Server - trying to install a video card


Try repeatadely pressing delete on startup with the monitor cable attached to your onboard graphics socket but keep the new graphics card in. then you should go into the bios. change the graphics setting to your graphics car and then save and reboot. ... Dell PowerEdge 1600SC Server

New video card wont work, acer monitor no signal


Ok the IGFX is the on motherboard video you will need to set the cmos to clear the setting you did or move the video cable to the motherboard output.after you have used the bios to switch back to the AGP you can start widows in safe mode to acc ... Acer X193W LCD Monitor

My VX924 Green Led Blinks until fully booted to windows


Ok if what im understanding is you tried on another computer and it worked great \015\012the monitor is not your problem the problem lies with your video card\015\012the video card could be outdated\015\012the video card could need ... ViewSonic VX924 19" LCD Monitor

Installed new video card but the signal remains black


REMOVE THE CARD AND UNINSTALL THE VIDEO CARD IN ADD REMOVE PROGRAMS. THEN REMOVE VIDEO CARD AND INSTALL DRIVERS THEN INSTALL YOUR VIDEO CARD. I HAVE THIS SAME VIDEO CARD AND HAD THE SAME PROBLEM.THIS WAS THE ONLY WAY I COULD GET IT TO WORK. ALSO YOU ... HP Pavilion A6010N (882780985575) PC Desktop

Screen stays black


Try using a different monitor if you have one available, or disconnect the monitor from the computer and then turn it on. If you see a logo or color bar or message saying no signal, then your monitor is OK and you should take a look at your video ca ... Acer Aspire 1414 Notebook

Gateway E-3200 no video signal


Hi! there,\015\012 there are common factors why no video on your screen.,right one factor is ram,the other are video card,processor and monitor\015\012you can't trouble shoot with out other computer available,tester cann't detecte ... Gateway PC Desktops

No Video Signal


Try resetting the bios. On the motherboard there is a battery that looks like a watch battery. Remove the battery, then replace it again. (make sure the computer is unplugged from the wall socket when you do this)\015\012\015\012Does th ... Gateway GT4015E AMD Athlon 64 3500+ 2.2GHz / 1GB DDR / 200GB HDD / DVDRW DL / DVD-Rom / Flash PC Desktop

Onboard VGA port disabled, in Vista


You should try to disable it in the hardware list. \015\012\015\012E-machines have an odd bios where not all the functions of the motherboard are available to the user.\015\012\015\012If you can find the make and model of your ... eMachines EL1210-11 PC Desktop

Signal to monitor goes in and out, mostly out


Hopefully, it is just the on board video that has gone bad, and not the motherboard. When you install a video card on a PC, that has on board or integrated video, you will need to access the BIOS screen on start up and disable the on board video. T ... Gateway GT5220 PC Desktop

Computer "turns on" i hear four to five beeps, but the monitor gets no signal. a friend gave me the computer, only once did i see it boot up fully but it froze up so i had to restart it and it wont work. everytime i try i get the same thing four or five beeps and monitor says no signal. so i dont know whats happening. its a gateway computer runing windows xp. thats all i know. i know the monitor is good cause i tested it on another computer.


Without knowing the exact frequency/length of the beeps my first guess would be a bad stick of ram or a bad video card. If there is more than one stick of ram in the computer try it with one of the sticks pulled, pulling each stick until it does boo ... Gateway GT5028 PC Desktop

No display - ON-chip VGA diabled in BIOS


Hi ... i think you might solve the problem by removing the battery from *********** board for about 30 seconds or even a few minutes to be sure...... this should reset your bios to factory settings... good luck ! ... Acer Aspire SA80 (ASA80UC4603) PC Desktop

Emachines d3315 video failed - no signal to monitor.


Hello,Is the system work using the old video card? if yes then, use it and then reconfigure the in the bios setup using the PCI video card. You can insert it simultaneously and then use first the old video in preparation for the configura ... eMachines T6524 PC Desktop

New video card - now an error message


Check the bios of the machine for\015\012\015\0121. disable onboard vga when pci is installed\015\012\015\0122. look for a setting like\015\012set acpi/usb buffers at top of memory\015\012\015\012this setting ... HP Compaq d530 PC Desktop

Gateway LCD powers on but has no picture


I have a Gateway FPD1730 LCD monitor. When I plug it into my Gateway 500x desktop the power light turns green and then says "Power Saving Mode" and then it goes black. It will occasionally flash on and have a picture and then go off. When I unplug th ... Sceptre X9G Komodo IV 19" Flat Panel LCD Monitor

Dell e510 won't make it to post


Unplug computer, disconnect all usb/monitor/internet, open it, hold power button until green led on the inside on the motherboard turns off, pop out the BIOS battery (looks like a big watch battery and use a small flathead screwdriver to depress the ... Dell Dimension E510 Dual Core 2.8 Ghz (847403171179) PC Desktop

My monitor when powered up gives me a no input signal for VGA and DVI and then goes into sleep mode after 15 seconds. I plugged in a second monitor and have a no signal message too. Should i replace the video card or has the monitor locked itself out. Please advise....Best Regards Beth.


Hey BethSounds like you are in a bit of trouble!Based on what you've told me, it looks like it might be a video card fault. However, a few things to check first are..Make sure the VGA & DVI are secured tightly ... HP f2105 21" LCD Monitor

Replaced motherboard but nothing comes up on the monitor & it won't turn off unless I unplug it


Slickbear,\015\012\015\012This new Motherboad has an On board video card that is likely set to be the default one to use. Try switching your monitor cable to the onboard SVGA plug. then boot up your PC.\015\012\015\012If you n ... E-Machines eMachines Desktop PC

Get a no vga signal on my monitor, then screen is blank what could it be ? thanks


The monitor is not detecting a signal from your video output. The video circuit may be blown. If it is a plug in card, try re-seating the card in the slot. Make sure your cable is seated good and there are no problems with it. If you have anoth ... CTX P772 17" LCD Monitor

I have a old computer (Dell) and a new flat screen (Dell) i hooked them up and the screen is black (won't work). It's a digital screen and a analog computer does this make a difference?


Not at all - as long as there is a VGA connection (analog) for the monitor, you're fine. Make sure that if you have a video card that you set your bios to automatically send the video signal through the card (where you'd hook your monitor cable to). ... Dell E193FP 19" LCD Monitor

Upgrading graphics card


I just added an EVGA GT440 to my Acer Veriton G-series that has Intel Integrated HD Graphics.The BIOS is Acer v.02.68.This turned out to be not as hard as some on the internet make it out to be. The BIOS had "DISABLE INTEGRATED GRAPHICS" grey ... Acer Aspire M3201 Phenom X3 8650 PC Desktop

Pc starts and runs but wont boot up monitor shows no signal


1) When you turn on the computer, watch and listen for: a) power supply fan, (power is on) b) chassis lights (power is on) c) ticking sound during memory test (the BIOS POST is running) d ... HP PC Desktops

Blank screen after boot up


This issue may occur if one of the following conditions is true: \015\012Cause 1\015\012\015\012 loadTOCNode(3, 'cause');\015\012 \015\012This issue may occur if you have a CD, a DVD or a floppy disk in your CD, DVD, or floppy drive ... Dell Dimension 3000 PC Desktop
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.7464 seconds