Having problems with your PC Desktops ?

New HDD Install Prob

\015 I install new hard drive bt cant able to access. what can i do?\015

Answers :

Basic Troubleshooting Tips after Installing a New Hard DriveBased on Seagate IDE hard drives.

If you have installed your drive and it does not function properly, perform the following basic checks:

Additional Troubleshooting Tips

If you have performed the preceding basic checks but the problem persists, follow these guidelines for troubleshooting specific cases: 
After you install your new drive, your computer will not boot, and no error message appears on the screen.
The screen remains blank when you power up the system. 
The system does not recognize the drive. 
The dealer partitioned and formatted the drive for you in the store, but the drive does not respond when you install it. 
The system hangs in FDISK or fails to create or save the partition record. 
The system error message, "Drive not Ready," appears. 
The FDISK error message, "No Fixed Disk Present," appears. 
The drive does not format to full capacity. 
The DOS message "Disk Boot Failure," "Non-System Disk" or "No ROM Basic - SYSTEM HALTED" appears. 
The system error message, "HDD controller failure" appears. 
After you install your new drive, your computer will not boot, and no error message appears on the screen.

Check your computer manual or BIOS manufacturer to determine whether your BIOS supports drives that have more than 4,092 cylinders. If your system has this limitation, use the following procedure to configure your computer:

Turn off your computer, open the case, and remove your new drive.

CAUTION: To avoid electrostatic discharge damage to your computer or hard drive, make sure you are well grounded before touching the drive, cable, connector or jumpers.

Move the jumper on the alternate-capacity jumper, as shown in Figure 6. This causes the drive to appear to your BIOS as having a 2.1-Gbyte capacity (4,092 cylinders, 16 heads, 63 sectors per track). You may need third-party partitioning software, such as Disk Manager, to achieve full capacity of the drive. 
Remount your drive in the computer and replace the computer cover. 
Insert a bootable system diskette into drive A and turn on the computer. It should boot from drive A and automatically detect the new drive as a 2.1 -Gbyte drive. 
Insert your DiscWizard diskette into drive A and type A:XDM. Then press ENTER. This runs the Disk Manager program. 
Follow the Disk Manager instructions to install the dynamic drive overlay and to partition and format your new drive to its full capacity. 
After Disk Manager is done, reboot your system. You should see the Disk Manager banner and be able to access the full capacity of your new drive. 

The screen remains blank when you power up the system. 
If the steps listed above do not remedy this problem, try the following: 
Make sure the monitor is plugged in and turned on. 
Check all cards. 
Make sure the video card is seated in its slot and secured with mounting screws. 
Turn off the computer and remove the drive host adapter. If the screen turns on after you reboot, the host adapter may be incompatible or defective. If so, see your dealer. 

The system does not recognize the drive. 
Check all cables. 
Make sure the power supply is adequate for system needs. 
Reboot the computer and listen to make sure the drive motor starts up. If the drive is very quiet, it may be difficult to hear its discs reach operating speed. If the drive motor does not start up, recheck all drive cables. 
Verify that for each drive, a drive-type is listed in the system setup program. 
Try rebooting your computer by pressing the CTRL, ALT and DELETE keys simultaneously. If the drive is recognized after you reboot the system, the computer BIOS test may be completing before the drive is ready. 
One solution is to slow the processor speed during startup. If your computer has a turbo switch, set it to slow speed before turning the computer on. If there is no turbo switch, you may be able to use keyboard commands; see your computer manual for details. After the computer is up and running, return the processor to the fast speed. 
Another solution is to warm-boot your computer after every power-on. 
Check for I/O address conflicts. To isolate the conflict, verify that the drive and host adapter are compatible with your computer. Turn off the computer and remove all the peripheral adapter cards except for the video card and host adapter. If the computer recognizes the drive when you reboot the computer, turn off the computer. Reinstall the other peripheral cards, one at a time, until the conflict reoccurs. After you have isolated the source of the address conflict, you can resolve the conflict by changing the 1/0 address of the peripheral that appears to cause the conflict. 
If Disk Manager has installed the DDO on your hard drive and you have booted directly from a diskette, the information in the boot record for the drive may not have been loaded. Make sure there is no diskette in drive A and reboot. If you want to boot from the diskette, follow the "Booting with a Diskette" instructions under "Advanced Disk Manager Options" on page 20. 

The dealer partitioned and formatted the drive for you in the store, but the drive does not respond when you install it. 
Reboot the computer and make sure the drive spins up. 
Check all cables. 
Make sure the power supply is adequate for system needs. 
Make sure the DOS or Windows version the dealer used to partition and format the drive is the same version you have installed in your computer. If it isn't, see your dealer. 
Verify the drive-type values in the system setup program. You must install the drive using the same drive-type values your dealer used to partition the drive. 
Check for 1/0 address conflicts between peripheral cards. 
Check for viruses. 

The system hangs in FDISK or fails to create or save the partition record. 
Check all cables. 
Your setup system diskette may be corrupted. Try using a backup diskette. 
Make the partitions smaller. 
Change the interrupt jumper setting on the host adapter. 
Some BIOS have a Track 0 protection feature that protects Track 0 from viruses. This may cause FDISK to hang the system. You must disable this feature in the system setup program before you can use FDISK. See your computer reference guide for assistance. Be sure to re-enable this important feature when FDISK is done. 

The system error message, "Drive not Ready," appears. 
Check all cable connections. Make sure pin 1 of the drive is connected to pin 1 of the hard-disc controller or host adapter. 
Make sure the power supply is adequate for system needs. 
Reboot the computer and make sure the drive spins up. 

The FDISK error message, "No Fixed Disk Present," appears. 
Make sure the power supply is adequate for system needs. 
Verify the drive-type values in the system setup program. 
Check for 1/0 address conflicts. 

The drive does not format to full capacity. 
Verify the drive-type values in the system setup program. One of the following problems may have occurred: 
The values may be set with an incorrect translation characteristic. 
You may have entered a parameter value that exceeds the physical capacity of the drive. 
You entered a translation characteristic that does not take full advantage of the drive's capacity. 
The drive's physical specifications exceed the translation limits imposed by the BIOS.

CAUTION: If you change the drive-type values in the system setup program, you must partition and format the drive again. This erases data on the drive. 

If you have partitioned the drive into individual logical drives, you may need to make the partitions smaller to access the full drive capacity. 
If your computer supports LBA mode, you may need to enable LBA mode in the system setup program to access the full capacity of the drive. Refer to your computer's reference guide to find out how to enable LBA. 
Your computer may not support drives that have more than 4,092 cylinders. Follow the instructions on page 25 for After you install your new drive, your computer will not boot, and no error message appears on the screen. 

The DOS message "Disk Boot Failure," "Non-System Disk" or "No ROM Basic - SYSTEM HALTED" appears. 
Reinstall the DOS system files using the DOS SYS utility. 
Check all cables. 
Use FDISK to verify that the primary partition is active. 
Check for viruses. 

The system error message, "HDD controller failure" appears. 
Confirm the jumper settings on the drive. 
Verify the drive-type settings in the system setup program.
If a problem persists, please search for a solution or post a question in our tech support forum in our Help Desk.

Repair Help & Product Troubleshooting for PC Desktops

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

New HDD Install Prob


Basic Troubleshooting Tips after Installing a New Hard DriveBased on Seagate IDE hard drives.If you have installed your drive and it does not function properly, perform the following basic checks:Additional Troubleshooting Tip ... PC Desktops

New HDD not recognising on laptop


Did you format and re-install your OS on your new hdd?is it set as master- jumper on rear of drive- where the power connector and ribbon connector connect? (little black, removable jumper connector) usually to the left of the ribbon connector- ... PC Laptops

Want to replace hard drive in desk top PC with a larger one (750 GB sata). I know how to install it and format and partition the drive.What I would like to know what is the best way to transfer every thing from old drive to new. OS Win XP home at present will be upgrading to a different version later.


Most new HDD come with imaging software that will allow you to "clone" the old HDD and transfer the information to the new HDD. If not, you will need an imaging program ie Norton Ghost, Easeus Todo Backup (free). These will take an image of your ol ... Gateway 3250S PC Desktop

Got a new hdd 250gb sata the pc can't find it


I have the exact same system you have and have the same problem. Dell quit supporting that system as far as updates to drivers and BIOS updates before SATA drives became readily available.The short answer is there is no way to boot to a ... Dell XPS™ 600 PC Desktop

I cannot open my zoombrowser 6.1 software.


\015\012 Why does Canon ZoomBrowser EX always crash on Vista?\015\012By ... Canon ES-E1 EOS Link (4593a006) for PC

XP won't recognize 2nd SATA drive and shows 1st SATA drive as drive F:


To get Windows to recognize the 2nd HDD, you have to initialize it in disk management.\015\012\015\012http://www.sim ... Dell Dimension 5100 (D51L1) PC Desktop

HOW DO I install new memory in acer aspire L320


The other expert's solution here gives you the information and practical steps you need to know about what to do to change the memory in a computer.here is some additional background information you should know specifically about the Acer Asp ... Acer Aspire L310 - Core 2 Duo E6300 1.86 GHz (S6479432) PC Desktop

Recovery partition - repair


You have obviously deleted the partition that the laptop could recover from but usually if you are supplied a cd to recover windows, there is normally a drivers folder within the cd but not the aplications, such as anti virus although these are only ... IBM ThinkPad T30 2366 Notebook

Can't reboot dell 4100 dimension desktop


First put the hdd installation cd into the cd drive and try to boot. This should install the hdd driver as well as start formatting the new hdd. After the drive is formatted take out the hdd cd & insert the Windows installation cd into the drive. ... Dell Dimension 4100 (-JM0TB01) PC Desktop

Samsung DVR HR 737 substitution Old original Hdd 160 GB (dead)


It stays on "Loading" because it can not find the necessary software that was installed on your original HD. (It's like installing a new HD in your computer without installing an Operating System.)You might try to clone the old drive to t ... Compaq EVO D510 CMT P4 2.5/20GB/256MB (268899999) PC Desktop

Not boot from factory CD -where is CMOS battery?


Hi,Appreciate the direct "Ask Me".Based on your post/description:\015\012\015\012Toshiba Satellite 1415-S173;\015\012new HDD;\015\012would ins ... Toshiba Satellite 1415-S173 Notebook

New Hard drive


Make sure you de-static yourself before touching either the HD or computer and make sure you take the battery out and unplug your laptop before you do anything. To de-static yourself, plant yourself in one spot, touch a piece of metal and make sure y ... PC Laptops

Cannot reinstall Windows XP pro to my hard drive which had it alr


I have found 2 websites taht can help you somewhat:\015\0121) this is the one with the steps that can help you, ... E-Machines eMachines Desktop PC

Removing RAM from Acer L320


The other expert's solution here gives you the information and practical\012 steps you need to know about what to do to change the memory in a \012computer.\012\012here is some additional background information you should know \012specificall ... PC Desktops

No boot device available - strike F1 to retry boot, F2 for setup utility after getting the blue screen of death


It is hard drive or HDD is damaged or corrupted, i will advice you to buy and upgrade to a new\015\012one and then install back the OS, I mean that you need to install back the operating system. Firstly\015\012open up the system and remove the old an ... Dell Dimension 8400 PC Desktop

Is it a bad mb ?


If the HDD is not recognized in the BIOS, windows will not be able to install on that drive. Did you move the HDD interposer from the old drive to the new one? (t is a small adapter that plugs on to the pins of the drive.) If you did, reinstall th ... Dell Inspiron B130 Notebook

Replace existing 40GB internal HDD in laptop with 160GB internal


Ok first of all Hi!Now in order to transfer the right stuff from your hard drive to the new one. You will need to follow these instructions and i provided you with 2 methods.\015\012\015\012LONG METHOD (USE NEW HARD DRIVE ... PC Laptops

Dell 6400 was functioning normally. Then a blue screen came on stating " fatal error occured, laptop needs to shut down ect..." I tried to re instal xp, then message came back " Set up did not find any hard drive installed on your computer ect..." Do I need to buy a new hard drive? Thanks.


In all notebooks and laptops you have Recovery CDs that you use in a situation like this. If you have the recovery disks, then insert the disk number 1 in to the drive and reboot. Follow the instructions and WIndows gets installed. You loose all data ... Dell Inspiron 6400 Notebook

How and what do I do, after I've installed a new HDD (Vista)


Insert your OS installation disk in the DVD drive, and boot from it (you can press F12 to select the media to boot from during startup, or you can change the order of boot devices in BIOS). It will kick off OS (I presume it's Vista) installation. Aft ... Dell Inspiron 1501 Notebook

Cannot get new Motherboard to boot up in Normal Mode


What u may have done is wwhen u were installing the new board, gave a static shock to the system...that will cause only the fans to come on and nothing more...this is a bad problem bc u cannot fix it...if u figure out something else is wrong, and it ... Gateway PC Desktops

I can re boot boot my compaq persario V6000


Only a HDD with a properly installed OS, a valid boot sector and an active partition will 'Boot' Did\015\012it ever work? Are you sure the POWER is there. Are you sure the cables\015\012are on right and the HDD is identified in the BIOS o ... HP Compaq Presario V6000T PC Notebook

Gatewat 4525GZ Intermittenly cant find DVD/CD Drive


I got similar problem to this one. the only diff. is it was saying hdd not installed. my chum's laptop was a Toshiba just abt a year old now... she brought it to me saying it crashed and she tried to installed it herself. but it doesnt complete its i ... Gateway 4525GZ Notebook

Can't restore, want to erase HDD and install over from scratch


U need a boot cd containing Partotionmagic program,by means of that u can delete partitions but dont delete 1st partition(its nesesary for recovery) add new partitons and reboot. ... PC Laptops

Laptop wont boot after new HDD install


I had this same problem yesterday. I went into the BIOS and under system configuration there was a SATA setting enabled, I disabled it and then the setup disk could find my drive. ... Compaq PC Laptops

New HDD = 80GB but, Bios sees >1TB unpartioned space.


Whenever you switch drives, you must access the BIOS and have it redetect the drive every time. Try the new drive again. Have the BIOS detect it. Use the Windows XP disk and do a full fomat (youll get an option to quick format it, but dont) If th ... Dell Latitude 110L Notebook
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.7406 seconds