Having problems with your PC Desktops ?

Front panel leads Emachine model T2862

\015 I disconnected the front panel leads from the mobo and looking for a pin-out diagram so i can reconnect them properly\015

Answers :

E-machine model T2862 pin-out for the 10-pin front panel header is screen-printed on my Emachine's motherboard, but is so small and far away from the actual pin location, that it is likely being overlooked. If looking into the computer case from the side where you remove the panel, the header looks like a row of four pins with one missing at the farthest right pin location, and a row of 5 pins underneath that, with the fifth pin directly below the missing (key) pin in the row above it. Starting on the first row, you would install the 2-pin connector from the front panel labeled "Power LED" to the leftmost and 2nd from the left pins. (You may need to switch it around to get it to work as the LED is polarized. You will know as soon as the system starts to boot up if it is on properly, as this light burns constantly if the unit is on.) Then, to the right of that connection, you would connect the 2-pin connector labeled "Power Switch" to the 3rd and 4th pins from the left on the first row. (It does not matter which way around this connector plugs on, as all we are really doing is allowing the front panel button to connect these pins together to turn the system's power supply on when you press the button.) OK! Drop down to the BOTTOM row of pins below the first row. To the leftmost and 2nd from the left pins on the second row you will install the connector labeled "HDD LED". (Again, you may have to switch it around to get it to work since it is polarized. You will have to watch the system boot up and as the hard drive is accessed, you will see it blinking randomly if it is connected properly. NOTE: You will not damage anything if this or the power LED is hooked up wrong. They simply will not function. So don't fret, just switch them around.) Next, the header has room to connect a reset switch if your system has one. (Mine does not.) You would install the 2-pin connector labeled "RESET" to the 3rd and 4th pins from the left on the second row of pins. (Again, this is a connector that works fine regardless of which way around you install it, as it simply lets the reset button connect these pins to reset the system when the button is pressed.) Finally, you will notice one pin is left unused below the missing (KEY) pin. As far as I know, this pin does nothing, but is likely a ground or maybe a source for DC power as I have seen before. The unused pin above it is for manufacturers who make one connector coming from the front of the case which is pre-wired with all these functions, so the connector (usually with 10 total possible wire locations) can have that one location sealed or capped to prevent someone from installing it the wrong way around and potentially sending voltages somewhere they shouldn't be going, or causing something to not work properly. I made a quick pic in MS Paint below for better reference:

9372ad7.jpg
What is the Series of the Unit? Most of these diagrams are available on the Manufacturers Website for just this reason, But I would need more information on the Model and Series of these computers to give you the URLs for this
\015\012Jamzie
Repair Help & Product Troubleshooting for PC Desktops

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Front panel leads Emachine model T2862


E-machine model T2862 pin-out for the 10-pin front panel header is screen-printed on my Emachine's motherboard, but is so small and far away from the actual pin location, that it is likely being overlooked. If looking into the computer case from the ... PC Desktops

Emachine t2742 I also have a wiring problem!


Gtater,It's ironic that you ask me this question today-- i am just now carrying in another eMachine computer to fix. Anyway, unfortunately I do not have one that is the same model as yours (T2742). However, I did some quick research and found t ... E-Machines eMachines Desktop PC

My t2862 powerlight will not come on but a green led comes on on the main board, nothing else happens. I also disconnected the pwr sw,hdd led and pwr led plugs and don't know which pins they go on. Thanks


On the front panel header where the wires connect, there are two rows of 5 pins. The top row actually has 4 pins with the end one missing, and the bottom row has 5 pins. The first two pins on the top row are for the power LED. The next two pins are f ... E-Machines T2862 PC Desktop

How does the power switch and led plug up on a GT5428 motherboard?


This is Gateway Support, and Support Documents for the Gateway GT5428 Desktop PC,http://support.gateway.com/s/pc/R/1009466/1009466nv.shtml ... Gateway GT5428 PC Desktop

How can I fix the 'on' button on my computer. It


After a while of use the front cover of the PC can come loose causing the issue you are describing. What I would do is turn off the computer (actually unplug it to ensure you don't get shocked) and remove the front-panel of the computer (usually acco ... Dell Dimension 4600 PC Desktop

HOW DO I install new memory in acer aspire L320


The other expert's solution here gives you the information and practical steps you need to know about what to do to change the memory in a computer.here is some additional background information you should know specifically about the Acer Asp ... Acer Aspire L310 - Core 2 Duo E6300 1.86 GHz (S6479432) PC Desktop

Removing RAM from Acer L320


The other expert's solution here gives you the information and practical\012 steps you need to know about what to do to change the memory in a \012computer.\012\012here is some additional background information you should know \012specificall ... PC Desktops

I have a T2958 and toof the face off. Can you


EMachines doesn't give out this kind of info, and I don't have one in the shop. eMachines also had the habit, of using a few different manufacturer's of motherboards. Intel, TriGem, MSI, Asus,and FIC to name five. Plus eMachines wou ... E-Machines (T2958) PC Desktop

Have emachine T1150 - the on off button when pushed in is getting stuck and machine will no longer turn on. Can this be fixed and is it worth the cost ? Can I fix myself ?


The switch on the outer plastic front panel is usually just a plastic peice with a spring, it pushes the button in on the inside metal housing of the computer case, therefore not really much to worry about, you just need to remove the front panel to ... E-Machines T1150 PC Desktop

Pinout on t6410 gATEWAY CONNECTING POWER BUTTON


I don't see that this problem was solved. Adding additional information.The eMachines T6410 Desktop PC uses an MSI MS-7145 motherboard.(MicroStar International ), ... E-Machines eMachines Desktop PC

Ibm 8303-21g front audio pin configuration


For AC97 Front Panel Audio\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012Pin\015\012Signal\015\012Description\015\012Pin\015\012Signal\015\012Description\015\012\015\0121\0 ... IBM PC Desktops

My 5150 would not start after the USB cable plugged to the front was kicked out. I suspect damaged to the starting panel. If that's the case would it work after replacing that front panel?


The front panel's usb ports may have broke, Unplug them to test..\015\012\015\012Open pc and look for the wires coming from the front panel,\015\012\015\012follow the wires and look for the one that plugs into the front usb po ... Dell Dimension 5150 (DIM515MIN) PC Desktop

Want to get front panel off Acer Desktop - Help!


Hi theretake off both the side panels, and look for screws behind the front panel, also look underneath the front panel for possible screws, once the screws have been removed the front panel should pop off and you will able to add your drive. ... Acer Aspire AM1100-B1410A Refurbished AMD Desktop PC - AMD Athlon X2 4000 2 .1GHz, 2GB DDR2, 320GB S ...

How to remove front panel. - PC Desktops


The front panel usually cannot be removed until you remove the side panels. The side panels are usually released by removing screws to them in the back and then it will slide in the direction of the the rear (sometimes the front). Then you can gain a ... PC Desktops

Cd drive My cd writer will not open, how can i fix this?


1.If the keyboard has a CD/DVD Eject key, press it. The Eject key is usually placed by the volume knob and is marked by a triangle pointing up with a line underneath. 2.Double-click My Computer . 3.Right-click the icon for the CD, CDR ... HP Pavilion a1330n (EL466AA) PC Desktop

I need a diagram for wiring a new power supply to a Gateway 509ge.


Although this problem is a year old, no solution was stated.Stating this in the hope it may help someone in the future;This is Gateway Support, and the main support page for the Gateway 509GE Desktop PC, ... Gateway 509GE PC Desktop

Can u possibly tell me where i might be able to download a schematic for an EMachine desktop computer model #T2742? It is out of warranty and was donated to our church and we need to know where to reconnect the main pwr switch wires and LED indicater (on/off) wires to the circuit boards ( 1 ea of red, white, blue).


Hi dallasblue08,\015\012\015\012Here's a diagram of what your looking for:\015\012\015\012The following eMachine models share the same motherboard (and thus the same front panel layout):T2742 T2796 T2798 T2824 T288 ... PC Desktops

My computer light turns on then off, no fan no screen


Changed the power supply and Power On switch?New parts? Okay. We'll come back to them. For now, lets look over some simple things.I can tell you that even after 20+ years as a tech, I still get a little zealous, when it comes to bui ... Smart Modular SV3170A

Need where pwr sw and pwr led and hdd led plug onto au31 motherboard


FIC AU31 mb (a.k.a K7m-NF18G mb)Pin Configuration = PinoutThe Front plastic panel of the computer is the Front Panel.The area of pins on the motherboard that the cables (Wires) go to, is the Front Panel header.Front Panel head ... E-Machines T3092 PC Desktop

How to remove ibm thinkcentre p4 3.0 motherboard


This is the link to the IBM ThinkCentre S50-8183, Hardware and Maintenance Manual,http://www-307.ibm. ... IBM ThinkCentre S50 8183 - P4 3 GHz (8183D9U) PC Desktop

Wires from switch came unplugged (white and black) where do they


Power On switch (Button)? Restart switch? Speakers?Wires came loose from the motherboard?Should like you to see if you can trace the wires back to the front panel, (Where the Power On button is located Granted, this may be a little tough ... E-Machines eMachines Desktop PC

I would like an internal view of eMachine T4150 to be sure everything is connected correctly


There's a bit of a toughie! eMachines doesn't like to give out this information, lyndapalimas, and I don't have one sitting in my shop.eMachines used four different motherboard manufacturers, to my knowledge. TriGem, Intel, FIC, and MSI. ... PC Desktops

Want to add an additional dvd rom to my packard bell IXTMX6618 but unable to remove the front panel can anyone help


1) Computer unplugged from power.2) Open the Side Panel. TOUCH the metal frame of the computer case BEFORE you reach inside! (Not shouting)Your body carries Static electricity. Static can fry out, (Short circuit), ... PC Desktops

How do you change the Hard Drive for a Sony Vaio vgn-tt180? And where is the oem hard drive located? Thanks, Mo


Not a recommended thing Mo. Granted I don't know your computer prowess, but it's an involved task, even for a tech.First you make a backup of what's on your harddrive now. Burn to disk/s, all of your personal stuff, (If you haven't ... Sony VAIO TT Series VGN-TT180N/B NoteBook Intel Core 2 Duo SU9400 11.1' Wide XGA 4GB Memory

Broken USB jack, no power.


1) Unplug the computer from power. Open the computer case.2) TOUCH the metal frame of the computer case. (Not shouting)This will relieve your body of Static electricity.3) Unplug the front panel USB cable from the mother ... Dell OptiPlex GX520 PC Desktop
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2389 seconds