Having problems with your PC Desktops ?

Emachine e1310 will turn on but will not stay on.


Answers :

This may be a heat problem or power supply issue.

If this is a heat issue, take of the case and blow out the dust with air compressor (just do this outside away from items you want to keep clean). Also clear away any debis from the CPU fan & heatsink (this can get caked on). Leave the case off for testing purposes and try it again. Take a look to see of the CPU fan to make sure it is moving well. If sputtering it may be your problem.

If you have a powersupply issue (which can be very common if your computer is more and a few years old). You may swap it out for about $30. Just make sure the output on the new one is at least the same (or more) than your old one. Hope this helps. Best Regards, -md
Repair Help & Product Troubleshooting for PC Desktops

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Emachine e1310 will turn on but will not stay on.


This may be a heat problem or power supply issue. If this is a heat issue, take of the case and blow out the dust with air compressor (just do this outside away from items you want to keep clean). Also clear away any debis from the CPU ... PC Desktops

Emachines , shutting off on it's own?


While it is possible the power supply could be going bad, usually it would not work intermittently like this.\015\012\015\012Most likely the motherboard is starting to go bad, I would do a quick visual inspection for any buldging or leaki ... E-Machines eMachines Desktop PC

Itt urns on but it stays on the emachine bootup


We can only try for a power drain for this issue,\015\012\015\012all you have to do is unplug the power cable from the computer and battery too, then press and hold the power button for 40sec( without battery and power chord), then connec ... E-Machines M5414 Notebook

W2686 eMachine doesnt turn on after changing powersupplies


I agree with the earlier poster that you have now excluded the PSU so it must me the mobo or CPU. I have a w2686 and can test it for you. I am currently trying to track down a restore disk for it. ... E-Machines eMachines W2686 PC Desktop

Emachine not turning off.


You can checkit by unhooking it on the inside from the mobo panal just remember where it ogoes back take a small flat head and cross the two prongs it comes of off then shut it down if it works look on ebay for a complete front panel with switch or o ... E-Machines eMachines Desktop PC

I have a EMachine T6534 which won't start. I shut


Most computer repair shops have a tester that they can hook up to your power supply. You can also purchase one for yourself, they usually run $25-50, it may be viable to purchase one if the shop will charge that much to test. ... PC Desktops

Processor? I have a T2792 emachine. The machine will shut down right in the middle of doing something, but doesn't power all the way off. The green power button turns a solid yellow and stays on along with the hard drive light and disk drive light. All the fans stay running. It's like it goes into hybernation, but the only way to get it back on is to hold in the power button, turn it off, and power back up. I'm running 1.5G ram and a 500W power supply. Any Idea's? Michael


The power box is going bad. It's a matter of time before it will not turn back on. you will see. i would get a new one from ebay and replace it. ... E-Machines eMachines Desktop PC

HELp EMACHINE My emachine will not boot up normally it keeps returning to the welcome Logo screen. i 've tried safe boot,and everthing on the F8 list i do not know what else to do? :(


I understand that your pc doesn't  load the operating system. I request you to please follow the trouble shooting steps I am providing you I am sure your issue must be resolved.I request you to please turn off your pc and ... E-Machines eMachines Desktop PC

Emachine tower won't turn on


Smps it is on cpu. where u connect power supplty cable it is 1 square box.it is on top[ of cpu back side. ... E-Machines eMachines Desktop PC

Emachines monitor goes black while CPU is still working


... E-Machines eMachines Monitor E15T4

Turn computer on, screen stays blank.


Hi there Eliot.It does sound like a graphics issue, go here and select "downloads" for all the drivers for that computer .http://www.emachines.com/support/product_support.html?cat=Notebooks&subcat=M%20Series&model=M5405 ... E-Machines M5405 Notebook

???HARD DRIVE CRASH??? ON DESKTOP EMACHINE


Hi!\015\012we'll do some basic troubleshooting here!\015\012okay, try to relax dont panic stay calm and stay focus we'll do it step by step.\015\0121. open your CPU (be sure to unplug it and loose it from any power connections) ... E-Machines eMachines Desktop PC

Monitor screen picture won't stay on for longer than a second


I had the same problem with my eMachine t3418. Site advisor Micromend suggested changing the power supply to more wattage. Very much recommend doing that. I did but it didn't fix the problem. Micromend also advised trying a video card. I bought ... E-Machines eMachines Monitor E15T4

My e-Machine W3115 automatically shuts down multiple times


1) Computer off, and unplugged from power. (Unplug from the surge protector FIRST, then unplug the power cable out of the power supply)2) Work on a table where you have plenty of room.Open the computer case. (Rear of computer, ... eMachines W3115 PC Desktop

My Emachine wont stay turned on


This can b caused by a few different problems\015\0121) The machine can be over heating, maybe due to a bad or slow running CPU Fan.\015\0122) Bad power supply\015\0123) Can b software problem, maybe a Virus\015\012Try turning ... E-Machines eMachines Desktop PC

My pc is an emachine but when i try to turn it on it automatically turns off but the fan is running


The power supply is bad. Electrolytic Capacitors inside the power supply. The 'Caps' are filters for the power supply. (Used in both the Input Stage, and Output Stage)Inside the power supply are Voltage Rails. The 3.3 volt rail, the 5 vol ... E-Machines eMachines Desktop PC

The yellow power led light blinks on front of the emachine w2646. The CPU Fan works. The power button will not turn the PC on or off, you just have to plug in the power cord to turn it on. The monitor just stays at a black screen. the Cpu Fan spins. i have replaced CPU, Ram, Power Supply. With no change to the system.


Did you flash the main board ??1.) remove battery2.) press and hold the power button for 10 - 30 seconds3.) replace battery.4.) when the system boots it will say press XX (e.g F2) to load defaults and continue ,, press t ... E-Machines eMachines Desktop PC

My laptop's screen stays black.


Can you see your screen as it should be when it is on by holding a flashlight on it.\015\012If so then it is probably your backlight that is gone.\015\012I am in the process of changing mine.\015\012Very cheap ... E-Machines PC Laptops

Emachine- will boot up 3-4 times before computer


This could either be a operating system problem or hardware. \015\012\015\012O/S problem could be actually caused by several things but eventually it might not work at all. It can also be caused by a recent and rather nasty virus going ar ... PC Desktops

Gatweway lap top button light up, but wont turn on


I'm afraid this sounds suspiciously like a motherboard problem. It would help to know what model etc, as some Gateway & EMachine model laptops have had extended warranties due to motherboard issues, or just go to Gateway.com and research it yours ... PC Laptops

Emachine beeps Hey, we just got a new emachine and we have the same problem! We got it mid/end of April but were in the process of moving so it stayed in the box till about a week ago. I hooked it up and when you press the on button it beeps 5 times then you hear the fan kick on like its thinking about starting up but then it just stops and beeps until you turn it off. The monitor says no signal and then goes blank. Any advise?


That would be a problem for e-machine. The beeps are codes. I will try to help, but it is hard to diagnose without looking at it.You can try several things. Open it up and make sure that everything is seated inside. Make sure the memo ... PC Desktops

Help i have a e17t4 monitor and i have pluged it in to 2 computers same thing happens on both comps i pluged the monitor to power i get blue lite then solid greenand stays green i can turn it off and onat this point but when i pluge it in to the computerafter sitting awile it comes on normale and shuts off and you cant turn it back on un less u un plug it for a while and then it will do the same thing


Hi crabguy,To my understanding, this is a common problem with some eMachine monitors (including the E17T4) since its production start sometime 2004/5.Your particular concern could be due to several possibilities:1. faili ... ViewSonic VA720 17" LCD Flat Panel Monitor

Emachine problems My emachine is a couple of years old. It has always worked great until this weekend. When you push the button to turn on the computer, the fan starts going fast and loud, but nothing else happens. The fan will stay on until we shut the computer down. The moniter is not showing a connection to the pc as well. Please let me know if you have any ideals.


My emachines is couple of years old but has ran great until now. We had a power outage and ever since then it will not come on, there is nothing. I have replaced the power supply and the mother board and still nothing.Could it be my processor?? model ... E-Machines eMachines Desktop PC

Emachine shut down


I have an emachine T3646 that is relatively new, when I hit the power button on the front it flashes and makes a solid beep but wont turn on, has anyone else had this problem? ... E-Machines eMachines Desktop PC

I have a 2 year old emachine that will no longer stay on. It was turning off by itself and slowly got worse and worse until it won't stay on at all. Any ideas? Virus?


Not likely.\015\012Sounds more like an overheating problem.\015\012I'll suggest to clean all the fans from dust and lint.\015\012You may also need to apply a fresh heat release compound on the processor.\015\012You may need pr ... E-Machines eMachines Desktop PC
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.8982 seconds