Having problems with your Computer Processors ?

No signal shows on monitor

\015 I have an Accer Aspire AST690-UP925A, problem is when i turn it on lights flash like it is booting up but not sure if it is because nothing shows on the monitor except when i turn the moniter on it shows ''no signal'' then turns off. Anyone know what causes this? Occasionally there is a beep along with it but not always. The monitor works just fine on other computers, but when i put other monitors on this comp. the same thing happens. Any ideas would be appreciated. Thanx\015

Answers :

When a computer beeps on start up there is a crucial input output piece of hardware no working. If you have any experience with computers check to make sure everything is conected right. I inclued a link for support for your computer. Larry

http://www.acerpanam.com/synapse/forms/portal20.cfm?website=AcerPanAm.com&siteid=7117&areaid=2&formid=3390&LINKTEXT=Support%20Solutions
Repair Help & Product Troubleshooting for Computer Processors

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My monitor not turn on when the computar turn on to . and when you try to turn on the monitor its like flash for 1 sec and tune off to black . to turn the monitor on i need to prees the botten 30 time on the monitor to turn him on.


First you sec your monitor power cable is not loos or power in properly if ok then you sec your monitor VGA cable is properly conect to your pc if ok then you disconnect your VGA cable in your pc then you power on your monitor and sec that youre mone ... PC Desktops

Monitor comes up shows "acer" then says no signal and goes black


The interface between the monitor and the cable might need replacement. Please check it. ... Acer AL2016 W 20" TFT LCD Monitor

I have a dell demension 4300 that recently started having issues, slow cutain effect, freeze ups. harddrive clicking away. Then one day I had the blue screen that said an error was detected. Then it wouldn't reconize the harddrive but it would go into the bios screen and then not do anything else. So I took it in to have it diagnosed and they said the edie circuit on the board was fried. They offered me a card option for the back but I opted to replace the motherboard with one that was listed as


CaSmogTech,There is a No Signal on the monitor because the monitor is not receiving a Video Signal.Your computer is not producing a video signal.In essence, your computer isn't working, because there is no Operating System on ... Dell Dimension 4300 PC Desktop

Monitor shows ''NO SIGNAL''


This is normal. The monitor is telling you it is not getting a signal from the computer, which is true because you've turned off the computer. The monitor power is still on, however. The monitor power is not controlled by the computer power switch. J ... Computer Monitors

My VX924 Green Led Blinks until fully booted to windows


Ok if what im understanding is you tried on another computer and it worked great \015\012the monitor is not your problem the problem lies with your video card\015\012the video card could be outdated\015\012the video card could need ... ViewSonic VX924 19" LCD Monitor

If you monitor is showing the message no signal this means that the monitor is not receiving a signal from your computer and/or receiving a signal that it does not understand. So the first thing I would do is remove any extra connectors between the computer and monitor like a KVM Switch. Next if you still have trouble I would try the monitor on another computer. If it works we know the problem is with the computer. If the issue is with the computer you may want to reset the video card to make su


Hi , check the pins in the monitor plug as they can be bent , and also check your mointor is set to accept an input from your lead ( serial/hdmi etc ) Some monitors have a built diagnostic which is often colour bars , if your monitor sh ... HP Media Center m1080n (PC099A#ABA) PC Desktop

Screen shows message "no input signal" and monitor goes to sleep.


Monitor show "no input singnal" error masage when not gating any type of video singnal ,\015\012so if u realy check your monitor wires for correctty plugged in . \015\012then:- Two possibilities:\015\012either the ... HP vp17 Monitor

NO SIGNAL What do I do?


These messages are normal when the computer truly goes into suspend mode or loses the video signal (such as when the computer is suddenly turned off).If the monitor displays any of these messages when the computer should be displaying vid ... HP PAVILION A6230N DESKTOP PC

Sony Monitor says "No Input Signal, switch to Power Save"


Hi. there has been a surge that has tripped the surge protector. this surge may have destroyed the mother board , in return, rendering the ICs dormant. you can test this theory but unplugging the CPU and moniter from this blown surge protector and pl ... Sony SDM-HS75/B 17" LCD Monitor

Gibberish + won't finish loading Windows


Remove the new memory first. if that does not help you may have some a virus, indicated by safe mode workng fine. One other thing i found would do that is a damaged Hard drive, not to likely here because safe mode works. ... Dell Dimension E521 PC Desktop

Monitor shows no signal


Ur monitor is "not" the problem... you have problem in ur PC..\015\012\015\012solutions:\015\012check loose graphic card\015\012remove ram. put them back again/... ... Intel (RK80532PG0881M) Pentium 4, 3 GHz Processor

No signal shows on monitor


When a computer beeps on start up there is a crucial input output piece of hardware no working. If you have any experience with computers check to make sure everything is conected right. I inclued a link for support for your computer. Larry ... Computer Processors

LG screen goes in stand by. I was using two monitors for several months, everything OK, now I decided to get a new LG Flatron instead of one of the monitors... and only this one goes in safe mode!! Two screens plugged in: Philips analogical working fine no problems. New LG Flatron digital goes in power save mode after few minutes Tried to plug in ONLY the LG, same problem after few minutes. Philips monitor no problems. So it HAS to be a screen function or problem of the LG? Computer: AMD + 3Ghz


Oke having a similar problem atm, this is what i have found so far. was trying to help a friend who has bought the same 19" LG monitor. When i connected the monitor to her PC i noticed that it was not the same connection as the previous one but it ha ... LG 19" Widescreen Flat Panel LCD Monitor

Power on - blank (black) screen


Disconnect the monitor signal cable from PC and switch on your monitor. It should show some logo with Red, Green and Blue colors with a message similar to "No signal". If so, your monitor is working fine. Sometimes if the brightness and contrast is ... Dell E152FP 15" Flat Panel LCD Monitor

My Lg Monitor wont show screen (Power Button Flashing)


The monitor is probably on protection.To start unplug monitor\015\012from power and from computer and test computer with different monitor\015\012to find out if it is monitor or computer fault.If it is computer fault and no vi ... LG Flatron L1750S 17" LCD Monitor

Gateway LCD powers on but has no picture


I have a Gateway FPD1730 LCD monitor. When I plug it into my Gateway 500x desktop the power light turns green and then says "Power Saving Mode" and then it goes black. It will occasionally flash on and have a picture and then go off. When I unplug th ... Sceptre X9G Komodo IV 19" Flat Panel LCD Monitor

DELL E153FPf doesn't show the image


OSD Warning Messages\015\012A warning message may appear on the screen indicating \015\012 that the monitor is out of sync range.\015\012\015\012 \015\012\015\012 \015\012 \015\012 \015\012 Cannot \015\012 Display This Video ... Dell E153FPf 15" TFT LCD Flat Panel Monitor

Monitor blue light comes on shows emachines logo and color bars then monitor turns off and light turns yellow


Your monitor is beleiving it is not receiving any signal from your pc. 1 make sure your cables are secure. 2 make sure your pc is on. 3 borrow a monitor from a freind to see if your pc is sending the signal out, if the borrowewed monitor is showing a ... E-Machines eMachines Monitor E15T4

Dell 24'' Ultrasharp went blank


I suspect the invertor supplying power to the Xenon backlight tubes has failed.\015\012This can be reapired but may not be cost effective.\015\012Ask for a quote from your local computer specialist but keep in mind the cost of a new monit ... Dell Computer Monitors

Problem with the monitor


Hi,The three boxes represent the built-in diagnostics of the monitor. The letters G is green, B is blue and R is for red, the 3 color guns of the picture tube of your monitor. The words "Self Test" indicates that it is in diagnostic mode ... Compaq FS7550 17" CRT Monitor

No signal The TV stopped showing a program and on the screen it read, "no signal". In the household there are two other TVs that operate OK. This is a cable TV setup. Checked the cables and they are all connected firmly


This problem requires you to test both the monitor and the signal input form you cable tv setup. Set the monitor up on a computer and see if it works properly. If it does then you may have a problem with the signal conversion of the cable tv to the ... Envision 19" Widescreen Flat Panel LCD Monitor

"No signal detected" when LCD connected with DVI-D Cable


Thank you for providing your configuration details.\015\012You have failed to specify wheather or not your LCD Display is under Warrenty.\015\012\015\012Perhaps these simple trouble shooting procedures will get the job done.\0 ... BenQ FP71E 17" LCD Monitor

RE:monitor goes black


Monitor going black after a few seconds can be causd by a faulty power supply or inverter. Some monitors have both as one unit.\015\012Sometimes it is basic failed capacitors, After that then I would look at transistors.\015\012The averag ... Acer AL2017 20" LCD Monitor

Monitor shows on receiving signal, will not display image.


Hello,The Viewsonic VX2235WM has a known issue with the power supply going out. The flashing power light or no picture is the classic symptoms of this issue. Check out our web site at: www.ccl-la.com. We have a step by step repair guide p ... ViewSonic VX2235WM Monitor

BENQ FP737S Monitor shows "No Signal Detected" on startup


First problem could be the hdmi cable you are using is loose or broken.second, the display mode you selected was wrong, try to go to desktop and right click and choose nvdia control panel and choose the nview display mode to use,select the only use o ... BenQ FP71E 17" LCD Monitor
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.5136 seconds