Having problems with your Computer Monitors ?

X203w shows 'no signal' when booting computer, but then has no display.

Answers :

The problem might most probably be with the VGA of the PC. Either try another monitor or another VGA card.
Repair Help & Product Troubleshooting for Computer Monitors

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

PCV-RS720G Sony Vaio : BFG 5500 installed and wont display

Hi thereBoot up in safe mode, F8 on start up, if it lets you into windows, go to the device manager and uninstall the graphics drivers, then reboot the pc, let the PC detect the new card and try install the drivers, have your driver CD in the C ... Sony VAIO PCV-RS720G (027242658103) PC Desktop

"No signal detected" when LCD connected with DVI-D Cable

Thank you for providing your configuration details.\015\012You have failed to specify wheather or not your LCD Display is under Warrenty.\015\012\015\012Perhaps these simple trouble shooting procedures will get the job done.\0 ... BenQ FP71E 17" LCD Monitor

Pc wont read monitor

If you look at the monitor there will be an led light on the front that is always orange or yellow when the computer is off but still connected to the monitor. This led will turn green when the computer boots up, sometimes even showing a "no signal" ... HP PAVILION A6230N DESKTOP PC

PC or monitor, signal problems

Your monitor is telling you it's on it's last legs..either that or your compaq has a bad video section. either is more vital than a video cable being loose. ... PC Desktops

Emachine destop not recognising acer lcd monitor

It sounds more like the computer isn't starting up. The "no signal" message is coming from the monitor itself to tell you it's on but there's nothing coming in to display. Normally no special drivers are required for the monitor, and you'd see at lea ... Microtek C593 15" Flat Panel LCD Monitor

EMachine W3107 will not boot, no display.

Have you tried a different Graphics Card, looks to me like the onboard graphics card is at fault, there should be an AGP slot or PCI slot that you can plug a new Graphics card into then you should be fine... ... PC Desktops

Red light on power up. No image on monitor. Pc fans working.

On a computer mainboard there are usually a number of connecting pins right next to one another called RESET, POWER LED, HD LED etc.The power led often leads to the green LED next your power button to show that the juice is available and on. Th ... Aspire Red X-Cruiser Mid Tower ATX Case without Power Supply (CSASXCRUSRD)

Pc starts and runs but wont boot up monitor shows no signal

1) When you turn on the computer, watch and listen for: a) power supply fan, (power is on) b) chassis lights (power is on) c) ticking sound during memory test (the BIOS POST is running) d ... HP PC Desktops

"No Signal" on monitor after boot

Hi try to use different slot on your motherboard see if that helps if not try different video card...if that didn't help it might be your motherboard that went bad ... HP Pavilion a400n (DQ173A#ABA) PC Desktop

I was adjusting picture on monitor and now picture completely messed up

\015\012Signal out of\015\012\011\011 Range.\015\012Out Of Scan Range\015\012Horizontal frequency is out of range.\015\012Cannot Display This Video M ... IBM E74 17" CRT Monitor

HP m7060n Media Center PC had boot problem: now won't display any

Lets try to repair it using the windows installation disc. First things first, look at the motherboard down on the right lower side. I would like you to find the CMOS jumper, it will be three pins sticking up with a plastic jumper made of plastic fit ... HP Media Center m7060n PC Desktop

The monitor turns off and on repeatedly.

There are lots of reasons why it can shutdown, but happerlly none should be serious. It may be that the B+ or Power supply is too high, look for a pot near the power supply and try turning it down a bit. Also the x-ray protection may be too high, loo ... ViewSonic VE710b 17" Flat Panel LCD Monitor

My computer wont boot up the fan and light turn on for a second then goes right off....

Follow these steps to determine why your computer won't turn on.\015\012\015\012Computer shows no sign of power ... HP Pavilion dv9000z Notebook

NO SIGNAL What do I do?

These messages are normal when the computer truly goes into suspend mode or loses the video signal (such as when the computer is suddenly turned off).If the monitor displays any of these messages when the computer should be displaying vid ... HP PAVILION A6230N DESKTOP PC

LG CB553H monitor has power and menu that sais no data. When I connect to a pc there is no display.

Hi,A monitor display showing "No Data" indicates that either the PC is not sending any usable video signal or the monitor is not capable of displaying the incoming video signal. To determine which is at fault, you wou ... Compaq FS 7550 17" CRT Monitor

Out of Range message displays when PC boots

To resolve this behavior, either change the refresh rate, or change the video adapter settings.\015\012To change the refresh rate:\015\012\015\012Restart\015\012the computer, and while it is restarting, press F8 ... Westinghouse 22" Widescreen LCD Flat Panel Monitor

My VX924 Green Led Blinks until fully booted to windows

Ok if what im understanding is you tried on another computer and it worked great \015\012the monitor is not your problem the problem lies with your video card\015\012the video card could be outdated\015\012the video card could need ... ViewSonic VX924 19" LCD Monitor

Gibberish + won't finish loading Windows

Remove the new memory first. if that does not help you may have some a virus, indicated by safe mode workng fine. One other thing i found would do that is a damaged Hard drive, not to likely here because safe mode works. ... Dell Dimension E521 PC Desktop

Get NO SIGNAL on Acer M1640~Monitor is Fine~Is CPU

Try removing the system memory and clean the brass contacts and the slots it goes into, then reseat the memory and try to boot again, the memory looks like this >>>>>>> ... Acer Aspire M1640 Refurbished Intel Desktop PC - Intel Pentium Dual Core E2160 1.8GHZ, 1GB DDR2, 120

Even if i switch on my computer with moniter it doesnt show anything on moniter screen it remains black

Hello. With the computer and monitor OFF, disconnect the signal cable from the video card on your system. Next, turn on the monitor. There should be a bright green box with a pink outline of a video connector inside showing. If there isn't, an ... Samsung 793S 17" CRT Monitor

Why does my computer swith on but not boot up

Hi Garnedd!\015\012 \015\012First of all, it sounds like you've taken a lot of troubleshooting steps thus far. So thank you for providing the details of those steps. It helps greatly.\015\012 ... Compaq D51S 1.6GHz Desktop XP Computer

I have an LG laptop connected to an external monitor. It has worked in the past. In the last week when i turned on my laptop the external motitor showed the boot up process right up until the final desktop screen appears when it says 'no signal'. I have managed to get the external motitor to display my background pic but nothing else. Help please.

There should be a button on the keyboard that controls the output...it is done by pressing the Fn key (function) in combination with the Fkey (all those F1..F2..and so on next to the Escape key) Also, you can Right click anywhere on the desktop (the ... PC Desktops

Monitor says no input signal

Do the icons look ok when you can see them? It sounds like your resolution may be way too high for the monitor. It loses sync and blanks the screen rather than show a lot of mess.\015\012\015\012Boot your windows in safe mode (tap F8 befo ... PC Desktops

How to format acer desktops - Acer PC Desktops

1 -. Must be clear that the format going to lose everything on it,\015\012it is necessary to support all those files that are important or if you\015\012do not miss. It is not a technician work, you can do that 2 -. You must have all the mother ... Acer PC Desktops

Monitor displays breifly then goes to blank screen

Try booting up your CPU again, while on its process of booting press F8, then select (something MODE), okay, then when you are at windows environment go to control panel, select display, set your display settings its default or 900 by 600 pixels sett ... Dell Dimension 4600 PC Desktop
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.7968 seconds